VBA7216
Product Specifications
VBA7216
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA7216 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA7216: a 20 V N channel in MSOP8 with a 0.74 V threshold
The VBA7216 is a single N channel MOSFET in an MSOP8 body with a 20 V drain to source rating, a plus or minus 12 V gate window, a 0.74 V threshold, a 7 A current figure and three resistance columns, 25 milliohm at 2.5 V, 25 milliohm at 4.5 V and 13 milliohm at 10 V.
The three columns have a shape worth reading twice. The resistance does not change at all between 2.5 V and 4.5 V, then halves at 10 V. A die that is flat between 2.5 and 4.5 and then improves by half at 10 V is a die whose channel is not yet fully formed at 4.5 V, which sits oddly with a 0.74 V threshold.
The likely explanation is that the 2.5 V and 4.5 V columns are the same measurement reported twice, or that both are limited by something other than the channel, such as the bond wires or the on resistance of the test setup. Either way, the honest reading is that this part should be driven at 10 V when its 13 milliohm matters, and that the 25 milliohm figure is what a 5 V gate gives.
Key data for the VBA7216
| Configuration | Single N channel |
| Package | MSOP8, surface mount, 0.65 mm pitch |
| VDS | 20 V |
| VGS | Plus or minus 12 V |
| Vth | 0.74 V |
| ID | 7 A |
| RDS(on) at 2.5 V | 25 milliohm |
| RDS(on) at 4.5 V | 25 milliohm |
| RDS(on) at 10 V | 13 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Thermal path | Eight leads, 0.65 mm pitch, less copper per lead than SOP8 |
| Board area | Roughly half of an SOP8 footprint |
What a 0.65 mm pitch body does to the thermal path
MSOP8 is an SOP8 shrunk in both directions, and the lead pitch falls from 1.27 mm to 0.65 mm. The leads are narrower and the solder joint area per lead is smaller, so the thermal resistance from junction to ambient is higher than in an SOP8 for the same die, typically 90 to 120 degrees per watt on a normal board.
At 13 milliohm and 7 A the conduction loss is 640 mW, which with 100 degrees per watt is a 64 C rise. That is the point where an MSOP8 part stops being a working switch and becomes a part that works on a bench. At 4 A the loss is 208 mW and the rise 21 C, which is comfortable.
The narrow pitch also changes the routing. Two traces at 0.65 mm pitch cannot both be wide, so the copper under the body is limited by the escape routing rather than by the available area. That is the practical reason the body is used for signal level and low current switching rather than power.
A 0.74 V threshold and a 12 V gate window
A 0.74 V threshold makes the part usable from a 1.8 V logic rail in principle, since 1.8 V gives more than a volt of overdrive. The 2.5 V column at 25 milliohm suggests otherwise: a die that reaches only 25 milliohm at 2.5 V is not a good 1.8 V switch, whatever its threshold says.
The 12 V gate window is tighter than the 20 V of the SOP8 parts on the same shelf. That matters when the gate is driven from a 12 V rail, because any overshoot on that rail exceeds the window. A 5 V or 10 V drive sits comfortably inside it.
The combination of a low threshold and a narrow gate window is a part for a low voltage system with a regulated gate rail: a 3.3 V or 5 V logic supply for the gate, a 12 V maximum rail, and a load of a few amps. It is not a part for a 12 V automotive rail where the gate sees load dump transients.
A 0.65 mm pitch body also changes the assembly window. The stencil aperture area ratio falls below the point where a 0.12 mm foil releases paste reliably, so the foil is usually 0.10 or 0.08 mm and the aperture is narrowed to keep the paste volume in proportion. A part placed with too much paste tilts on its leads and one side lifts during reflow, which shows up as an open on the second and seventh leads long after the board has passed inspection. For a first build the placement height and the reflow profile deserve the same attention as the die.
Where it fits
It fits a load switch on a 5 V rail, a synchronous buck in a space constrained module, a battery protection switch in a wearable, and a level shifting stage where the body height matters. It does not fit a 12 V rail without a gate clamp, and it does not fit a 7 A continuous load in still air.
Our kitting service page covers how a set of parts is assembled for a build, which is where a small body part like this usually arrives, on a reel that has to match the feeder width.
The sourcing side of this part is covered on the NPI production launch checklist. For a small body part that arrives on a narrow reel, that page covers what is checked before the first production build.
Questions we get on this code
Why is the 2.5 V column the same as the 4.5 V column? The catalogue prints 25 milliohm for both. Read the data sheet before relying on either, because a flat pair usually means one measurement was copied.
Can it be driven from 1.8 V logic? The threshold allows it and the resistance does not. Use 5 V or more for the gate when the current is above an amp.
Does the 0.65 mm pitch need a different stencil? Yes, the aperture area ratio changes with the pitch, and the paste volume has to come down with it.
Is the body available on a 3000 piece reel? We confirm the reel size and the feeder width on the quotation.