Contact Us

VBA5606

Brand: VBsemi
VBsemi VBA5606 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA5606 — Discrete & Power Semiconductors | Superb Automation

VBA5606

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA5606 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA5606: a 60 V N and P pair with 8 and 15 milliohm

The VBA5606 is a complementary pair in an SOP8 body rated at plus or minus 60 V, with a plus or minus 20 V gate window, thresholds of 2.8 V on the N side and minus 1.8 V on the P side, currents of 13 A and minus 10 A, and resistances of 8 and 15 milliohm at 4.5 V falling to 6 and 12 milliohm at 10 V.

Those are low resistances for a complementary pair at 60 V, and the current figures follow them. This is a pair built to carry real current in a small body, not a signal level stage, and that changes which numbers matter: the thermal path through eight leads becomes the limit long before the die does.

The two thresholds are far apart, 2.8 V and minus 1.8 V, which means the pair cannot be driven from a single 3.3 V logic signal without care. At 3.3 V the N side has 0.5 V of overdrive over a 2.8 V threshold and the P side has 5.1 V, so the two halves behave completely differently.

Key data for the VBA5606

ConfigurationDual, one N channel and one P channel
PackageSOP8, surface mount, 1.27 mm pitch
VDSPlus or minus 60 V
VGSPlus or minus 20 V
Vth, N channel2.8 V
Vth, P channelMinus 1.8 V
ID, N channel13 A
ID, P channelMinus 10 A
RDS(on), N, 4.5 V and 10 V8 and 6 milliohm
RDS(on), P, 4.5 V and 10 V15 and 12 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Thermal pathEight leads, shared frame, both dies dissipating at once

A 2.8 V threshold on the N side is the deciding number

A 2.8 V threshold is high for a logic level part. It means the die needs a gate well above 4.5 V to be properly enhanced, which is consistent with the resistance being published at 4.5 V and 10 V rather than at 2.5 V. A 3.3 V rail gives 0.5 V of overdrive, and the resistance at that point is not published and will be far above 8 milliohm.

The P side is the opposite: a minus 1.8 V threshold with the gate pulled to ground on a 12 V rail gives a gate source voltage of minus 12 V, which is deep enhancement, and the 12 milliohm column applies. Driving both halves from one 5 V signal is possible for the P side and marginal for the N side, so a driver with a 10 V output is the honest answer for this pair.

The threshold spread across the two dies is also a crossover issue. In a push pull stage the N side turns on later and the P side earlier, so a common gate signal produces a short interval at low current where neither device is properly on. At 10 V of drive the interval is short; at 3.3 V it can be the whole transition.

Thirteen amps through an SOP8

At 6 milliohm and 13 A the N channel dissipates 1.0 W. At 12 milliohm and 10 A the P channel dissipates 1.2 W. A stage that conducts through one device at a time is therefore dissipating about 1 W, which an SOP8 can pass on a board with a good copper landing and about 60 degrees per watt junction to ambient.

If both devices conduct simultaneously, in a bridge or a class D output, the total is 2.2 W and the body cannot pass it in still air. That is the case to check before the current is fixed, and it is the reason a complementary pair with these resistances belongs in a switching stage with a low duty on each device rather than in a linear one.

The body diodes are part of the thermal picture in any inductive load. During the freewheel interval the diode of the opposite device conducts, and its forward drop times the current is a loss that the catalogue page does not characterise. For a motor or a relay coil that interval can be a significant share of the period.

The threshold spread between the two dies also sets how the pair behaves at power up. With a 2.8 V N threshold and a 5 V logic rail, the N side is barely enhanced while the P side is fully on, so a push pull stage driven from one signal starts with an asymmetric output and a short interval of current through both devices. A driver that ramps the gate from 0 to 10 V passes through the same region, only faster, and the loss during the ramp is what the gate resistor controls. Measuring the supply current during a start up is the cheapest way to see whether that interval is acceptable.

Where it fits

It fits a 48 V push pull stage at a few amps continuous, a class D output at moderate power, a high side and low side pair in a small motor driver, and a level shifting stage where the two halves carry different currents. It does not fit a 60 V rail, and it does not fit a single 3.3 V gate signal.

Our strategic sourcing page covers how the supply of a family is held for the life of a product, which matters for a matched pair because the two dies have to stay matched across lots.

The sourcing side of this part is covered on the vendor consolidation. For a matched pair bought for a single programme, that page covers which lines stay dual sourced.

Questions we get on this code

Can both halves be driven from one 5 V signal? The P side is fine and the N side is marginal at a 2.8 V threshold. A 10 V driver is the reliable choice.

Is the pair matched? It is matched in voltage and not in resistance, 6 against 12 milliohm, which is the normal asymmetry between electron and hole conduction.

What is the loss in a bridge? Add the conduction loss of whichever device is on during each interval plus the diode loss in the freewheel interval, and compare the total with what eight leads can pass.

Do you supply it as a matched set? We quote from one lot where possible so that the two dies on a board come from the same wafer run.