Contact Us

VBA4338

Brand: VBsemi
VBsemi VBA4338 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA4338 — Discrete & Power Semiconductors | Superb Automation

VBA4338

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA4338 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA4338: two minus 30 V P channels in one SOP8

The VBA4338 is a dual P channel MOSFET in an SOP8 body with minus 30 V per device, a plus or minus 20 V gate window, a minus 1.7 V threshold, a drain current of minus 7.3 A and resistances of 45 milliohm at 4.5 V and 35 milliohm at 10 V, on trench silicon.

Two P channels in one body answers a specific need: a bidirectional switch, or two high side switches that work together. Back to back P channels block current in both directions when off, which a single device cannot do because its body diode conducts whatever the gate says. That is the arrangement used for a battery path that has to be truly isolated, and it needs two devices with their sources tied or their drains tied.

The cost is the silicon. A minus 30 V P channel at 35 milliohm is a large die, and two of them in an SOP8 body put a lot of silicon on one lead frame with no exposed pad to take the heat away.

Key data for the VBA4338

ConfigurationDual P channel, two independent devices
PackageSOP8, surface mount, 1.27 mm pitch
VDSMinus 30 V per device
VGSPlus or minus 20 V
VthMinus 1.7 V
IDMinus 7.3 A
RDS(on) at 4.5 V45 milliohm per channel
RDS(on) at 10 V35 milliohm per channel
TechnologyTrench
Gate chargeNot published on the catalogue page
Body diodeOne per channel, the reason a single device cannot isolate
Thermal pathEight leads, shared frame, no exposed pad
Pin mapNot published on the catalogue page

45 milliohm at 4.5 V is a P channel number

Forty five milliohm from a 30 V P channel at 4.5 V is what P channel silicon costs. The same current in an N channel of the same voltage class would be 8 to 12 milliohm in the same body, because holes carry less current per unit area than electrons. That factor of three to four is the price of the simpler gate drive, and it is why P channels live at low current and N channels live at high current.

At 4 A per channel the loss is 720 mW, and two channels conducting give 1.44 W in a body that has no exposed pad. At 2 A per channel the loss is 360 mW total, which is comfortable. So the practical working point of this part is a few amps per channel, not the 7.3 A headline.

The 10 V column at 35 milliohm is only 22 per cent better than the 4.5 V column, which means the die is well enhanced at 4.5 V. That is a virtue for a 5 V system, where the gate source voltage equals the rail and the 4.5 V column is the real number.

Back to back, and what the pair has to survive

Two P channels in series with their sources tied and their gates driven together form a switch that blocks in both directions when off. When on, one device carries the current through its channel and the other through its channel in the other direction, so the on resistance is the sum of the two, 70 milliohm at 10 V.

The arrangement is used at the battery terminal of a portable product, where the requirement is that the pack cannot be charged or discharged when the switch is off. A single P channel would leak through its body diode in one direction, which fails the requirement even though the channel is off.

During a fault the pair has to survive the fault current until the protection circuit reacts. The catalogue page does not publish a safe operating area, so that interval has to be checked against the data sheet, and the protection delay has to be short enough that the die stays inside it.

Two P channels that form a back to back pair have to be matched closely enough that they turn on and off within the same window. A 0.3 V difference in threshold, which is well inside a normal production spread, means one device is fully on while the other is still in its linear region, and during that interval the pair dissipates several watts for no useful purpose. Buying both channels from one package solves this by construction, since the two dies sit on the same frame from the same wafer, and that is a stronger argument for the dual body than the board area saving.

Where it fits

It fits a battery isolation pair on a 12 V or 24 V pack, two high side switches that share a gate signal, and a bidirectional analog switch at low current. It does not fit a 30 V rail, and it does not fit a path that carries more than about 4 A per channel continuously.

Our component shortage forecast page covers how a shortage is seen before it stops a line, which matters for a dual P channel because the second source list for this body is short.

The sourcing side of this part is covered on the excess inventory management. For a pair bought in programme quantities, that page covers how excess is identified and how age is handled.

Questions we get on this code

Can one channel block reverse current on its own? No. The body diode conducts with the gate off, so a true block needs the pair.

What is the on resistance of the pair? The sum of the two channels, 70 milliohm at 10 V and 90 milliohm at 4.5 V, when both are driven fully on.

Are the two gates separate pins? The catalogue does not publish the pin map. A pair driven together needs the gates accessible separately or tied internally, and only the data sheet says which.

Is 30 V enough for a 24 V pack? A charged 24 V pack is 27 to 29 V, so the margin is a few volts at best. Use a 40 V or 60 V part for a 24 V pack.