Contact Us

VBA3328

Brand: VBsemi
VBsemi VBA3328 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA3328 — Discrete & Power Semiconductors | Superb Automation

VBA3328

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA3328 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA3328: two 30 V N channels at 6.8 and 6.0 A in SOP8

The VBA3328 is a dual N channel MOSFET in an SOP8 body with 30 V per device, a plus or minus 20 V gate window, a 1.7 V threshold, current figures of 6.8 A simultaneous and 6.0 A single, and resistances of 26 milliohm at 4.5 V and 22 milliohm at 10 V, on trench silicon.

The two current figures are worth more than the resistance table, because they answer the question that a dual package always raises: what happens when both channels conduct at once. The catalogue is saying that the pair carries 6.8 A in total when both are on and 6.0 A through one channel alone, and that ordering is unusual and worth reading twice.

Most dual packages quote the same number twice, which leaves the reader to guess. Here the simultaneous figure is the larger one, which means the number was set by the lead frame rather than by the die: the frame can pass 6.8 A of total current, and a single die is limited to 6.0 A by its own bond wires.

Key data for the VBA3328

ConfigurationDual N channel, two independent devices
PackageSOP8, surface mount, 1.27 mm pitch
VDS30 V per device
VGSPlus or minus 20 V
Vth1.7 V
ID6.0 A single, 6.8 A with both channels on
RDS(on) at 4.5 V26 milliohm
RDS(on) at 10 V22 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Body diodeOne per channel, both anodes at their own source
Thermal pathEight leads, shared frame
Pin mapNot published on the catalogue page

Reading 6.8 A simultaneous against 6.0 A single

At 26 milliohm and 6.8 A shared between two channels, 3.4 A each, the total conduction loss is 600 mW and each die dissipates 300 mW. At 6 A in one channel the loss is 936 mW in a single die. So the simultaneous case is actually the easier one thermally, which is why the lead frame current can be higher than the single channel figure.

The single channel limit of 6.0 A is therefore a bond wire and die limit, and at 26 milliohm it corresponds to 936 mW in one die. That is a sensible limit for a small die on a shared frame, and it explains why the simultaneous figure is not simply half.

For a board that uses both channels as load switches on two rails, the practical current is 3 A each with a comfortable margin. For a board that uses one channel as a real switch and the other as a level shifter, the 6 A figure applies to the switch and the shifter carries milliamps.

Two channels that share a frame and a temperature

In a dual package the two dies are attached to the same copper frame, and the frame is the thermal path for both. If one die runs hot, the frame runs hot, and the second die starts from a higher temperature than its own dissipation would give. The effect is small at 300 mW per die and significant at 900 mW, which is why a dual package should not be used with both channels near their single channel limit.

The electrical side is quieter. Two independent N channels with separate gates and separate drains do not interact electrically at low frequency, and at high frequency the shared source impedance is the only coupling, which shows up as a small shift in the gate waveform of the channel that switches second.

Where the dual package earns its place is a pair of switches that always work together: two low side legs of a bridge, two parallel paths for a redundant supply, two segments of an LED string. In those cases the shared temperature is an advantage rather than a problem, because the two dies are meant to be at the same temperature.

The dual body also changes what a derating curve means. A single die in its own package is derated against its own dissipation; here the derating has to be applied to the total, because the frame and the moulding compound are common. A practical routine is to add the two conduction losses, compare the sum with what the body can pass at the intended ambient, and then confirm that neither die is above its own bond wire limit. With 3 A per channel both tests pass, with 5 A per channel the second one usually fails first.

Where it fits

It fits two load switches on adjacent rails, a redundant supply path, a two segment LED driver, and a low side pair in a small motor bridge. It does not fit a half bridge, and it does not fit a circuit that needs one channel at 6 A while the other is also working.

Our supplier scorecard page covers how a source is scored across a programme, which for a dual in a small body matters because the pin map and the current split have to stay the same from lot to lot.

The sourcing side of this part is covered on the safety stock planning. For a dual that ships on a shared frame, that page covers how a buffer is sized against the build plan.

Questions we get on this code

Which current applies to my board? If both channels conduct, use 6.8 A total. If one conducts and the other is a signal level switch, use 6.0 A for the conducting one.

Are the two channels identical dies? The catalogue gives one resistance pair for both, so treat them as matched, and confirm the pin map on the data sheet.

Can one channel be paralleled with the other? Only with separate gate resistors. Two dies on one frame with one gate node will not share current evenly during the crossover.

Is 30 V enough for a 24 V rail? No. A 24 V rail at plus 10 per cent is 26.4 V and leaves less than 4 V of margin for the switch node ring.