VBA3310
Product Specifications
VBA3310
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA3310 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA3310: two 30 V N channels in one SOP8
The VBA3310 is a dual N channel MOSFET in an SOP8 body with a 30 V drain to source rating per device, a plus or minus 20 V gate window, a 1.7 V threshold, a combined current figure of 13.5 A and resistances of 12 milliohm at 4.5 V and 10 milliohm at 10 V, on trench silicon.
Two independent N channels in one body is a board space decision before it is an electrical one. Two SOP8 packages occupy about 60 square millimetres including the clearance between them; one package occupies half of that plus the routing. On a board where the two switches sit next to each other anyway, for example two low side legs of a motor bridge or two load switches on adjacent rails, the saving is real.
The cost is thermal and electrical coupling. Both dies sit on one lead frame, so heat from one reaches the other through the frame and the moulding compound, and the thermal resistance from junction to ambient for each die is worse than it would be in a single package with a dedicated lead frame.
Key data for the VBA3310
| Configuration | Dual N channel, two independent devices |
| Package | SOP8, surface mount, 1.27 mm pitch |
| VDS | 30 V per device |
| VGS | Plus or minus 20 V |
| Vth | 1.7 V |
| ID | 13.5 A, read as a package figure |
| RDS(on) at 4.5 V | 12 milliohm |
| RDS(on) at 10 V | 10 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page, and it matters twice here |
| Channel to channel coupling | Shared lead frame, so heat and a common source impedance |
| Thermal path | Eight leads carrying the heat of both dies |
| Pin map | Not published on the catalogue page, confirm before committing a footprint |
Is 13.5 A per channel or for the package
The catalogue prints one current figure for a two die part, which is ambiguous by construction. Two readings are possible: 13.5 A through one channel while the other is off, or 13.5 A shared between the two in simultaneous conduction. The resistance column does not resolve it either, because it is also printed once.
The thermal arithmetic gives a usable answer. At 12 milliohm and 13.5 A the loss in one die is 2.2 W, which an SOP8 lead frame cannot pass in still air. At 6 A the loss is 430 mW per die and 860 mW for both, which is inside what eight leads can carry with reasonable copper. So the practical reading is 13.5 A for a single die with the other idle, and about 6 A each when both conduct at once.
That distinction matters in a motor bridge where both legs can conduct together during a direction change, and it matters in a converter where the two switches never conduct simultaneously but the heat from one still reaches the other through the frame. In the second case the average dissipation is half, so the coupling matters less.
Two dies, one lead frame, and the source impedance
In a dual package the two sources usually come out on separate pins, but they still share the lead frame and the die attach. At high switching frequency a common source inductance of a nanohenry is enough to slow the gate drive and to couple the two channels, and the effect is invisible in a catalogue table.
For low frequency switching, which is what a load switch pair or a motor leg does, the coupling is irrelevant and the package is a pure space saving. For a 200 kHz converter the coupling has to be examined on the data sheet, and the routing of the source return becomes the deciding feature of the board rather than the die.
The other consequence of one package is that a failure in one die can take the other with it. A shorted die raises the temperature of the frame, and the second die sees the rise within seconds. In a safety related product that has to be argued in a failure mode analysis, and two separate packages make the argument easier.
Two channels that switch at the same instant also share the current in a way that the catalogue cannot describe. If the two gates are tied together and the sources have different trace lengths, one channel turns on earlier and takes the whole inrush for the duration of the mismatch, which for a few nanohenries and a fast edge is tens of nanoseconds. That is long enough to matter when the load is capacitive and short enough that the die survives it. The fix is not a bigger die but a symmetric connection: equal gate traces, equal source returns, and one resistor per gate rather than one resistor for the pair.
Where it fits
It fits a pair of low side switches on adjacent rails, a two phase low current buck, a small motor bridge with two low side legs, and a battery path where two parallel switches share a current. It does not fit a half bridge, because the two drains are not connected to a common switch node in this configuration.
Our BOM scrubbing page covers how a bill of material is checked before release, and a dual package is where a substitution looks harmless on paper and changes the thermal model, the pin map and the fault behaviour at once.
The sourcing side of this part is covered on the supplier onboarding checklist. For a dual in one body that has to stay pin compatible, that page covers what a new source documents first.
Questions we get on this code
Can the two channels be paralleled for more current? Only with separate gate resistors and a symmetric drain and source connection. Paralleling inside one package still leaves the lead frame as the limit.
Are the drains common or separate? The catalogue describes two independent N channels, so the drains come out separately. Confirm on the data sheet before the footprint is fixed.
What is the advantage over two single parts? Board area and one placement instead of two. The disadvantage is thermal coupling and a higher junction to ambient resistance per die.
Can it be used at 24 V? Not with margin. A 24 V rail at plus 10 per cent is 26.4 V and a switch node ring adds several volts, so the 30 V rating is reached.