Contact Us

VBA1206

Brand: VBsemi
VBsemi VBA1206 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA1206 — Discrete & Power Semiconductors | Superb Automation

VBA1206

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA1206 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA1206: a 20 V N channel in SOP8 that is specified at a 2.5 V gate

The VBA1206 is a single N channel MOSFET in an SOP8 body with a 20 V drain to source rating, a plus or minus 12 V gate window, a threshold window of 0.5 to 1.5 V and a drain current of 15 A. The catalogue quotes 8 milliohm at a 2.5 V gate and 6 milliohm at 4.5 V, on trench silicon.

The interesting part of that list is the gate column. Most parts in this voltage class publish their resistance at 4.5 V and 10 V, which suits a 12 V rail or a driver with a regulator. This one publishes 2.5 V and 4.5 V and nothing at 10 V, which is a statement about the die: it is a low threshold device that is meant to be switched by a logic rail, not by a 12 V gate drive.

A threshold window of 0.5 to 1.5 V is wide, and the width is deliberate. It lets the part turn on from a 1.8 V or 3.3 V logic output with margin at cold temperature, and it keeps the die out of a deep enhancement state at zero gate so the channel is fully off above a few microamps. The cost of a low threshold is a smaller noise margin on the gate node, so a gate resistor to ground matters whenever the driving pin is high impedance during reset.

Key data for the VBA1206

ConfigurationSingle N channel
PackageSOP8, surface mount, 1.27 mm pitch
VDS20 V
VGSPlus or minus 12 V
Vth0.5 to 1.5 V
ID15 A
RDS(on) at 2.5 V8 milliohm
RDS(on) at 4.5 V6 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page, ask for the curve before sizing a driver
Body diodeIntrinsic, anode at source, conducts when the source is above the drain
Thermal pathLead frame to the board, no exposed pad in this body
IsolationNot applicable, three terminal device

What an 8 milliohm column at 2.5 V really tells you

A 2.5 V specification is a hard test for a 20 V die. The gate sits 2.5 V above the source, the threshold can be as high as 1.5 V at the top of the window, so the guaranteed overdrive at the worst die is one volt. A trench cell that reaches 8 milliohm with one volt of overdrive has a thin gate oxide and a high cell density, and both of those raise the gate capacitance per unit area.

The practical consequence is that the driving pin has to supply charge, not just a voltage. At 20 kHz with a few nanocoulombs of gate charge the current is small enough for a microcontroller pin through a 22 ohm resistor. At 300 kHz the same pin may spend more time in its linear region than the switch spends in conduction, and the switching loss ends up in the driver rather than in the die. Since this catalogue page does not publish gate charge, the figure has to come from the data sheet before a switching frequency is fixed.

The 6 milliohm column at 4.5 V is the one to use when a small regulator or a dedicated gate driver feeds the gate. It is only 25 per cent better than the 2.5 V column, which is the signature of a die that is already close to its fully enhanced state at 2.5 V. A part whose two columns differ by a factor of two is one that is being pushed hard at the lower voltage and will behave very differently across a production spread.

15 A in an SOP8 body

Fifteen amps is a die and lead frame figure, not a working current in still air. SOP8 has no exposed pad, so the whole of the heat leaves through the eight leads into the copper they are soldered to, and the junction to ambient resistance of that path is typically in the 60 to 90 degrees per watt range on a normal board with a modest copper landing.

At 6 milliohm and 15 A the conduction loss alone is 1.35 W. With 70 degrees per watt that is a 95 C rise, which takes a 60 C ambient to 155 C and leaves no margin at all. At 8 A the loss falls to 384 mW and the rise to about 27 C, which is comfortable. Between those two points sits the honest continuous rating for a real board, and it depends more on the copper area under the leads than on the die.

Pulsed operation looks different. A load switch that closes into a capacitive load draws a current spike set by the load capacitance and the total loop resistance, and the die survives it if the pulse is shorter than the thermal time constant of the silicon, which is tens of microseconds. The number to check is the safe operating area chart at the applied gate voltage, and this catalogue page does not carry one, so a board that relies on a pulse above about 30 A has to be confirmed against the data sheet.

Where the part fits and where it does not

It fits a load switch on a 12 V or 5 V rail, a low side switch in a small DC-DC converter, an LED string return, a relay or solenoid driver where the coil current is under a few amps, and any place where a 3.3 V logic output has to control a power path without a gate driver. It does not fit a 20 V rail that rings, because the rating is the rail voltage and there is no avalanche margin in a trench die of this class.

Our power management cross reference page covers how a candidate is compared with an original part on the parameters that decide behaviour rather than the ones printed in a headline, and a low threshold logic level switch is exactly the case where the threshold window and the gate charge decide whether a substitute works.

The sourcing side of this part is covered on the component lead time solutions. For a logic level switch that a board cannot run without, that page covers what is done when the quoted date moves.

Questions we get on this code

Can a 1.8 V microcontroller pin drive it? At 1.8 V the overdrive over a 1.5 V threshold is 300 mV, which is not enough to reach the published resistance. Use a 3.3 V rail, a small level shifter, or a part with a threshold nearer 0.6 V maximum.

Is the 12 V gate limit a problem on a 12 V rail? Yes, if the gate is pulled to the rail. The window is plus or minus 12 V, so a 12 V rail with any overshoot exceeds it. Drive the gate from a lower rail, or clamp the gate node.

What should a purchase order carry? Part number, SOP8 body, reel size and date code requirement. We confirm the reel size on the offer rather than assuming it.

Do you hold stock? We quote from what is confirmed at the time of the request, and the answer for a specific quantity comes back with the quotation.