Contact Us

VBA1158N

Brand: VBsemi
VBsemi VBA1158N is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA1158N — Discrete & Power Semiconductors | Superb Automation

VBA1158N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA1158N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA1158N: a 150 V N channel in an SOP8

The VBA1158N is a single N channel MOSFET in an SOP8 body with a 150 V drain to source rating, a plus or minus 20 V gate window, a threshold of 2.5 V, a drain current of 5.4 A, and an on resistance of 80 milliohm at a 10 V gate.

One hundred and fifty volts is the next step above the 100 V family, and it costs resistance: 80 milliohm against 8 in the same body. That is the physics of a longer drift region, and it means this part carries amps rather than tens of amps.

The applications are the ones where 100 V is not enough margin: a 96 V battery string, a 110 V DC bus, the primary side of an offline converter below 100 W, and the high side of a power over ethernet injector at 57 V with a surge requirement.

Key data for the VBA1158N

ConfigurationSingle N channel
PackageSOP8, surface mount, eight leads
VDS150 V
VGSPlus or minus 20 V
Vth2.5 V
ID5.4 A
RDS(on) at 10 V80 milliohm
RDS(on) at 4.5 VNot published, and with a 2.5 V threshold it is far above the 10 V figure
TechnologyTrench
Gate chargeNot published on the catalogue page
Thermal limitAbout 1 W with the leads on copper
Body diodeIntrinsic, anode at source, recovery not published

Five amps at 80 milliohm and the body behind it

At 5.4 A and 80 milliohm the loss is 2.3 W, which is beyond an SOP8 in still air. The rating is a die figure and the working current is lower: 3 A gives 720 milliwatt and a 45 C rise on a good pad, which is comfortable, and 4 A gives 1.28 W and a 80 C rise, which is at the limit in a warm box.

So the honest range is 2.5 to 3.5 A continuous. That is enough for an offline auxiliary supply at 60 W, a 110 V DC bus load switch at low current, and the start up path of a motor drive, but not for a main power rail.

The thermal path is the eight leads. An SOP8 is a modest package and its limit is the reason the 150 V family stops at this current in this body: a larger die would need a DFN with an exposed pad, and that changes the assembly.

A 2.5 V threshold at 150 V is a deliberate choice

At 150 V the gate oxide is thicker for the field, and a 2.5 V threshold keeps the part drivable from 10 V without a special supply. That matters in offline circuits, where a 12 V housekeeping rail is usually available and a dedicated gate supply is not.

It also means the part must not be driven at 5 V. The overdrive would be 2.5 V and the resistance would be several times the published figure, which at 3 A turns a 720 milliwatt loss into two watts and makes the thermal calculation wrong.

The 20 V gate window allows a 12 V drive with the usual margin. In a flyback or a forward converter the gate is driven through a resistor from the controller, and a 10 to 22 ohm resistor keeps the edge at a few tens of nanoseconds, which is fast enough for 100 to 200 kHz and slow enough to keep the ringing inside the rating.

One hundred and fifty volts on a 110 V bus

A 110 V DC bus with a 20 per cent tolerance reaches 132 V, and the switch node ring on top of that can pass 150 V. The rating is therefore the minimum that makes sense, not a comfortable margin. A snubber and a short loop are part of the circuit at this voltage, and a transient suppressor across the bus is the second line of defence.

At 150 V the creepage inside an SOP8 is worth a thought. The leads are on a 1.27 mm pitch and the plastic is thin, so a polluted board at 150 V can track. A conformal coat or a slot in the board under the package is the usual mitigation where the environment is not clean.

Our kitting service page covers how a group of parts is assembled for a build, which for a high voltage supply is the practical way to buy, because the switch, the diode, the controller and the passives all have to arrive together for a line to start.

The sourcing side of this part is covered on the excess inventory management. For a 150 V part bought for one programme, that page covers how excess is identified and how age is handled.

Questions we get on this code

Can it replace a 100 V part? Only with the resistance penalty. A 100 V part at 20 milliohm and this part at 80 milliohm are not interchangeable in a thermal sense even though the footprint matches.

Is 5.4 A the working current? No. Two and a half to three and a half amps continuous on a good pad.

What drive does it need? Ten volts or more. A 5 V gate is outside the published data and gives a much higher resistance.

Does it have avalanche capability? Not published on the catalogue page, so a circuit that can put inductive energy into the drain has to clamp it externally.