VBA1106N
Product Specifications
VBA1106N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA1106N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA1106N: the 6.8 A member of the 100 V SOP8 family
The VBA1106N is a single N channel MOSFET in an SOP8 body with a 100 V drain to source rating, a plus or minus 20 V gate window, a threshold of 1.8 V, a drain current of 6.8 A, and an on resistance of 69 milliohm at a 4.5 V gate and 51 milliohm at 10 V.
It is the low current member of the family and it exists for a reason: a 51 milliohm die in an SOP8 is a small die, which means low gate charge and a fast switch, and in a converter that runs at a few hundred kilohertz and a few amps, gate charge matters more than resistances.
The 1.8 V threshold keeps it usable from a 5 V logic drive, which is what a small auxiliary converter usually has available.
Key data for the VBA1106N
| Configuration | Single N channel |
| Package | SOP8, surface mount, eight leads |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 1.8 V |
| ID | 6.8 A |
| RDS(on) at 4.5 V | 69 milliohm |
| RDS(on) at 10 V | 51 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page, expected low at this die size |
| Thermal limit | About 1 W with the leads on copper |
| Body diode | Intrinsic, anode at source |
Six amps against a one watt body
At 6.8 A and 51 milliohm the loss is 2.4 W, which is above what an SOP8 passes in still air. The rating is therefore a die figure and the working current is much lower. At 3 A the loss is 459 milliwatt and the junction rise is about 30 C on a good pad, which is comfortable. At 4.5 A it is 1.03 W and the junction rises about 65 C, which is at the limit in a warm enclosure.
So the honest working range is 3 to 4 A continuous, with spikes to the rating for short periods. That is fine for the applications this part suits, which are auxiliary supplies and control paths rather than power rails.
The thermal path is through the eight leads into the copper. An SOP8 with all eight leads on a plane is a better thermal package than its plastic body suggests, and it is much better than a SOT23 six lead, which is why the same order of resistance carries twice the current here.
Low gate charge as the reason to choose it
In a 300 kHz flyback or forward converter running 3 A, the switching loss can exceed the conduction loss. The gate charge sets the driver loss directly and the crossover loss indirectly, and a small die with 51 milliohm has perhaps a third of the charge of a 9 milliohm die in the same body.
That is why a family like this has four members with the same voltage and the same body and different currents. The choice is not which one is best, it is which loss dominates the board. At 2 A and 400 kHz, the small die wins. At 8 A and 100 kHz, the large die wins.
The 1.8 V threshold suits a 5 V drive, where the overdrive is 3.2 V and the 69 milliohm column applies. At 10 V the part reaches 51 milliohm, and the 35 per cent improvement suggests the die is not fully enhanced at 5 V, so a 10 V drive is worth having where the loss budget is tight.
Where it fits
It fits an auxiliary supply that runs from a 48 V or 60 V bus and delivers 2 to 4 A at a low voltage, a relay or solenoid driver on a high voltage rail, a PFC bootstrap path, and a small active clamp. It does not fit a main power path at 8 A, and it does not fit a circuit that needs a fast body diode, because the recovery of a 100 V die at this size is not published and is usually the limiting parameter in a hard switched bridge.
Our supplier quality audit page covers what is asked of a source before it is approved, and this class of part is where a source audit pays, because the same body and the same marking are used across a family whose members differ by a factor of three in die size.
The sourcing side of this part is covered on the NPI production launch checklist. For a part that is chosen late in a project, that page covers what is checked before the first production build.
Questions we get on this code
Is it a drop in for the 10 A part? In the same body and pin assignment, yes, but with less current capability. The other direction is not safe.
How much current in a closed box? Three to four amps on a good pad. Above that the leads and the plastic limit the part.
What about the gate resistor? 10 to 22 ohm is typical at this die size. A larger resistor slows the edge and reduces ringing, at the cost of crossover loss.
Is it available in a smaller reel? SOP8 usually ships at 2500 or 3000 pieces, with a smaller option for prototypes. We confirm on the offer.