VB5610N
Product Specifications
VB5610N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB5610N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB5610N: an N and a P channel rated at 60 V
The VB5610N is a complementary dual, one N channel and one P channel, in a SOT23 six lead body. Both are rated at plus or minus 60 V drain to source, the gate window is plus or minus 20 V, the thresholds are 1.8 V and minus 1.7 V, the current is plus or minus 4 A, and the on resistance is quoted as 8 milliohm for each channel at a 4.5 V gate and 10 milliohm at 10 V.
A complementary pair at 60 V is the gate drive stage of choice in a 48 V system, because it can pull a big device's gate low and high without a floating supply and without a level shifter. That is why the pair exists at this voltage: not to carry power, but to move charge fast.
The two resistance columns on this page need care. They run in the direction opposite to every other part in the band, and that has to be dealt with rather than smoothed over.
Key data for the VB5610N
| Configuration | Dual, one N channel and one P channel |
| Package | SOT23, six leads, surface mount |
| VDS | Plus or minus 60 V |
| VGS | Plus or minus 20 V |
| Vth, N channel | 1.8 V |
| Vth, P channel | Minus 1.7 V |
| ID | Plus or minus 4 A |
| RDS(on) at 4.5 V | 8 milliohm per channel as printed |
| RDS(on) at 10 V | 10 milliohm per channel as printed |
| Technology | Trench |
| Consistency note | The 10 V column is worse than the 4.5 V column, which is not physical, so the two columns have to be confirmed before use |
| Thermal limit | About 400 to 500 milliwatt in total for the body |
When the two gate columns run the wrong way
On every other part in this band the resistance falls as the gate voltage rises. Here it rises from 8 to 10 milliohm between 4.5 and 10 V, which cannot be a property of the silicon. Three explanations are plausible and all of them are the vendor's to resolve.
The first is a column swap in the catalogue table, in which case the real figures are 10 milliohm at 4.5 V and 8 at 10 V. The second is that the 8 milliohm row belongs to a different measurement condition, such as a lower current or a different temperature, and the two numbers are not comparable. The third is that the row was copied from a family table for a different die.
For a buyer the practical answer is the same in all three cases: the board should be built on the 10 milliohm figure, which is the conservative reading, and the exact value should be confirmed from the data sheet before a thermal calculation is signed off. An 8 milliohm channel and a 10 milliohm channel differ by 25 per cent of conduction loss, which on a 2 A gate drive stage is a few tens of milliwatts and not a rework.
A pair that moves charge rather than power
The typical use is a gate drive buffer. The N channel sinks the gate of a large MOSFET to ground and the P channel pulls it to the rail, and the current is limited by the gate resistor of the big device rather than by this pair. Peak currents of 1 to 2 A for a hundred nanoseconds are the normal duty, well inside the 4 A figure and well inside the thermal limit because the average is tiny.
In that duty the parameter that matters is not the on resistance but the gate charge and the threshold match. A pair whose N channel turns on at 1.8 V and whose P channel turns on at 1.7 V switches cleanly from a 5 V logic drive, with a short interval where both are off, which is what a gate drive stage wants.
For a linear use, where the pair carries a continuous current, the thermal limit arrives at about 1.5 A per channel and the 4 A figure is a die limit. The two uses should not be confused: this is a switching part.
Sixty volts of rating in a 48 V circuit
A complementary pair in a 48 V system has both channels referenced to nodes that move between ground and the rail, so the package sees the full rail difference between adjacent pins. The pin spacing of a six lead SOT23 is small, and at 48 V in a humid environment the creepage matters. A conformal coat or a larger body is the answer where the environment is not controlled.
The gate window is the other constraint. A P channel whose source sits at 48 V cannot have its gate pulled to ground, so the drive network has to keep the gate at least 20 V below the source and at most 20 V above it. A resistor divider between the rail and ground, with a clamp, is the standard arrangement.
Our vendor consolidation page covers how a supply is consolidated without losing cover, which is the right frame for a complementary pair, because the N and P dice usually come from the same family and a substitution has to move both at once.
The sourcing side of this part is covered on the sourcing audit trail. For a part whose catalogue table needs confirming, that page covers what record is kept of the checks made before an order.
Questions we get on this code
Which resistance figure should be used in a calculation? Ten milliohm, the conservative reading of the two columns, until the data sheet resolves the direction.
Can it drive a large MOSFET gate directly? Yes, that is its purpose. Add a resistor at the driven gate and check that the peak current stays inside the 4 A figure.
Is the pair matched in threshold? Within 0.1 V as printed, which is close enough that a 5 V drive turns both on with a small dead interval.
What is the reel and the date code? Six lead SOT23 normally ships at 3000 pieces. We confirm the reel on the offer and quote current production unless a date window is requested.