Contact Us

VB3222

Brand: VBsemi
VBsemi VB3222 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VB3222 — Discrete & Power Semiconductors | Superb Automation

VB3222

VBsemi — Discrete & Power Semiconductors

Product Overview

The VB3222 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VB3222: two 20 V N channels in a six lead SOT23

The VB3222 is a dual N channel MOSFET in a SOT23 six lead body, with a 20 V drain to source rating, a plus or minus 12 V gate window, a threshold between 0.5 and 1.5 V, a drain current of 6 A, and an on resistance of 28 milliohm at a 2.5 V gate and 22 milliohm at 4.5 V.

Two 20 V channels in one small body is a workhorse arrangement: a pair of load switches, the two halves of a bidirectional block, a synchronous rectifier pair on a low voltage output, or the low side switches of two separate rails driven from one controller.

The limits are the same as any small body. The gate window is 12 V, so the gate cannot sit at a 12 V rail, and the current figure is a die limit rather than a working current.

Key data for the VB3222

ConfigurationDual N channel, independent
PackageSOT23, six leads, surface mount
VDS20 V
VGSPlus or minus 12 V
Vth0.5 to 1.5 V
ID6 A
RDS(on) at 2.5 V28 milliohm
RDS(on) at 4.5 V22 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Thermal limitAbout 400 to 500 milliwatt in total for the body
Number of diceTwo, separate gates and sources

Twenty two milliohm per channel and what two channels cost together

At 2 A per channel and 22 milliohm, each channel dissipates 88 milliwatt and the pair dissipates 176, which is comfortable for a six lead SOT23 on a normal pad. At 3 A each it is 198 milliwatt per channel and 396 for the pair, which is at the practical limit. At 4 A each the pair dissipates 704 milliwatt and the junction is above 150 C in a 60 C ambient.

That gives a simple rule for this part: two channels at 3 A, or one channel at 4 A, in a warm enclosure. The 6 A figure applies to a single channel at a case temperature that only a copper plane can hold.

Switching loss adds to the sum. A 12 V rail switched at 100 kHz with a few nanocoulombs of gate charge gives a driver loss of tens of milliwatts per channel, which is small, and a crossover loss that depends on the gate resistor. At 300 kHz and above the crossover term can match the conduction term, which is why the gate charge matters even on a part whose data sheet page does not publish it.

The 12 V window and a 5 V system

In a 5 V system the gate window is not a constraint: a 5 V drive sits at 42 per cent of the rating and a 12 V transient is survivable. The window becomes a constraint when the part is used as a high side switch on a 12 V rail, where the gate must be pulled below the source by a bootstrapped driver and the gate to source voltage is the rail itself.

The standard fix is a resistor and a zener at the gate, or a driver with an internal clamp. Either way the part is usable at 12 V, just not with a bare connection.

The 0.5 to 1.5 V threshold window means the part turns on hard at 4.5 V and is usable at 2.5 V, where the resistance rises from 22 to 28 milliohm. That is a small penalty for a 27 per cent lower gate drive, and it makes the part friendly to a 3.3 V microcontroller pin, which sits between the two columns at an estimated 24 to 25 milliohm.

Two channels, one pad, and the trap in assuming independence

Separate gates and separate sources do not mean separate thermal paths. Both dice sit on the same lead frame in a six lead SOT23, and the lead frame is the only way heat leaves. A board that runs one channel at 1 A and the other at 4 A puts a hot die next to a cool one and the pair reaches a higher junction than either would alone.

There is also a coupling path through the package. A fast edge on one drain couples into the other through the lead frame inductance, which matters when one channel switches a 5 A load and the other carries a sensitive analog signal. In that case the two channels of one package are the wrong arrangement and two separate parts are right.

Our BOM consolidation page covers how two lines collapse into one package, and this part is a textbook case: it saves a reel, a feeder and 4 square millimetres, and it concentrates the thermal load in one small area, which is a trade a buyer should make knowingly.

The sourcing side of this part is covered on the BOM shortage recovery. For a dual that sits in the power path of a shipping product, that page covers how a line is kept running when one code goes short.

Questions we get on this code

Is 6 A for both channels together? It is one current figure. Treat it as a single channel at a 25 C case, and derate to about 2.5 to 3 A per channel when both conduct.

Can the gates be driven from the same pin? Yes if both channels switch together and the driver can supply the combined gate charge. Two gates on one pin doubles the capacitance and halves the edge speed.

Does it block in both directions? No. A single N channel conducts through its body diode in reverse whatever the gate does, so reverse blocking needs a second device in series, drain to drain.

What is the alternative with a wider gate window? The A variant of this family carries 20 V. Ask for it by code if the 12 V window is the constraint.