Contact Us

ADG721BRMZ

Brand: Analog Devices
Analog Devices ADG721BRMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG721BRMZ — Analog & Mixed-Signal ICs | Superb Automation

ADG721BRMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG721BRMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG721BRMZ: dual 4 ohm SPST switch, normally open, 200 MHz bandwidth

The ADG721BRMZ is a pair of normally open single pole single throw switches in an 8-lead MSOP. On resistance is 4 ohm maximum at 5 V and 10 ohm maximum at 3 V, the -3 dB bandwidth is above 200 MHz, and the switching times are 20 ns on and 10 ns off. The supply range is 1.8 V to 5.5 V, so the part runs from the same rail as a battery powered processor and passes a signal up to that rail.

Published values

ParameterValue
Configuration2 SPST switches, normally open
On resistance4 ohm maximum at 5 V, 10 ohm maximum at 3 V
On resistance flatnesslow, specified over the signal range
-3 dB bandwidthgreater than 200 MHz
Turn on time20 ns
Turn off time10 ns
Supply range1.8 V to 5.5 V single
Leakagelow, specified over temperature
LogicTTL and CMOS compatible
Packages8-lead MSOP and 3 mm by 2 mm LFCSP
FamilyADG722 normally closed, ADG723 one of each

Normally open in a battery product

A normally open switch draws no current from the control line when it is off and disconnects the load when the processor is in reset. In a battery product that is the state that matters: a signal path that is open while the system boots cannot load a sensor or drag a reference down, and the leakage path through the switch is the only current that flows.

The 4 ohm figure at 5 V becomes 10 ohm at 3 V, so a channel specified on a bench supply and then run from a lithium cell has two and a half times the resistance. Into a 1 kohm load that is 1 percent instead of 0.4 percent, and a gain calibration made at 5 V is wrong at 3 V.

200 MHz of bandwidth from a switch

A switch with more than 200 MHz of bandwidth passes a video signal or a fast multiplexed channel without rounding the edges. That figure comes from a small on capacitance, which is also what keeps the off isolation high: a switch with a large parasitic capacitance couples the open channel to the bus and the isolation falls as the frequency rises.

The 20 ns turn on and 10 ns turn off are fast enough for a pulse generator, a sample and hold or a chopper stabilised amplifier. In a chopper the switch resistance modulates the input, so the 4 ohm figure and its flatness become a noise term rather than a gain error, and the asymmetry between 20 ns and 10 ns is what gives the charge injection its sign.

Two switches and the die they share

The ADG721 has two normally open switches, the ADG722 has two normally closed, and the ADG723 has one of each with break before make action between them. The three are the same silicon with a different control inversion, so the choice is a system decision about the safe state and not a performance decision.

The 3 mm by 2 mm LFCSP version is for a board where the MSOP is too tall or too wide, and the electrical behaviour is the same. The exposed pad of the LFCSP is not connected electrically, so a board that pours copper under the part has to keep the pad isolated from any signal net.

The pages that answer this most often are the obsolete part cross reference hub for the family alternatives, one stop BOM sourcing for the acceptance test, and component lead time solutions for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

What is the difference between the ADG721, ADG722 and ADG723? The ADG721 has two normally open switches, the ADG722 has two normally closed switches, and the ADG723 has one of each. The silicon is the same and only the control polarity differs.

Can this switch pass a 5 V signal on a 3.3 V supply? No. The signal range is limited by the supply, so the rail has to be at least as high as the largest signal. The 5.5 V maximum supply is the ceiling for both.