AD8620ARZ
Product Specifications
AD8620ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8620ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8620ARZ: dual JFET amplifier, 6 nanovolts and plus or minus 13 volts
The AD8620ARZ is a two channel JFET input amplifier in an 8-lead SOIC that runs from plus or minus 5 V to plus or minus 13 V with 6 nV/root Hz of voltage noise, 10 pA of maximum bias current and 25 MHz of gain bandwidth. It is the part for a high impedance source that also has to be quiet and fast: a photodiode preamp, an instrumentation front end or an audio transducer stage running on a split supply.
Published values
| Parameter | Value |
|---|---|
| Offset voltage, B grade | 45 uV typical, 150 uV maximum |
| Offset voltage, A grade | 85 uV typical, 250 uV maximum |
| Offset voltage drift | 0.5 uV/C typical, 1.5 uV/C maximum on the B grade |
| Input bias current | plus or minus 10 pA maximum |
| Supply current per amplifier | 2.5 mA at plus or minus 5 V, 3.0 mA at plus or minus 13 V |
| Gain bandwidth | 25 MHz |
| Slew rate | 40 V/us typical, 50 V/us at plus or minus 13 V |
| Voltage noise density | 6 nV/root Hz at 1 kHz |
| Noise, 0.1 Hz to 10 Hz | 1.8 uV p-p |
| Settling to 0.01% | 350 ns on a 4 V step at plus or minus 5 V |
| CMRR and PSRR | 90 dB minimum, 95 to 110 dB typical |
| Supply range | plus or minus 5 V to plus or minus 13 V |
Ten picoamps is what makes a high impedance source usable
A bipolar input with 4 uA of bias current would develop 4 mV across a 1 kOhm resistor, which is why current feedback parts cannot sit on a photodiode. Ten picoamps into 10 MOhm is 100 uV, still small against the 150 uV offset, so a 10 MOhm transimpedance stage can be built without a bias compensation resistor. At 100 MOhm the same bias current is 1 mV and the resistor's own thermal noise, 1.3 uV/root Hz at that value, becomes the dominant term.
Why this part needs a split supply
The minimum supply is plus or minus 5 V, so it does not fit a 3.3 V single rail system at all. That is a consequence of the JFET input stage, which needs headroom above the source to keep its junction reverse biased. A modern CMOS part with 1 pA of bias current covers most of the same sockets on a single 5 V rail and is the reason this family is now specified mainly in analog instruments that already have a split supply.
Six nanovolts and forty volts per microsecond
The combination of 6 nV/root Hz and 40 V/us is unusual: most low noise JFET parts are an order of magnitude slower. In a transimpedance stage with 100 pF of photodiode capacitance and a 1 MOhm feedback resistor, the closed loop bandwidth is set by the feedback pole and the gain bandwidth together, and 25 MHz makes the amplifier transparent. In an audio gain stage the 1.8 uV p-p of low frequency noise and the 0.5 uV/C drift keep the DC offset out of the output coupling capacitor.
Grades and what they cost
Two grades are published. The B grade gives 150 uV maximum offset with 1.5 uV/C drift, and the A grade gives 250 uV with 3.5 uV/C. In a DC coupled instrument the grade difference is worth more than the price difference, because the drift figure is what the calibration has to hold against over temperature.
The pages that answer this most often are the amplifier cross reference for the family alternatives, defense grade components for the acceptance test, and component lead time solutions for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Will the AD8620ARZ work on a single 5 V supply? No. The minimum supply is plus or minus 5 V, so a single rail system needs a charge pump or a different part. A CMOS input amplifier with a 1 pA bias current covers most of the same sockets from a single rail.
How much output swing is available? Plus or minus 3.8 V minimum into a 1 kOhm load on a plus or minus 5 V supply, which leaves about 1.2 V of headroom at each rail.