Contact Us
  • Home
  • BLOG
  • How Do You Read a PCB Cross-Section Report?

How Do You Read a PCB Cross-Section Report?

Read a cross-section report in a fixed order and against the class you actually bought. Barrel copper first, then the knee, then the annular ring, then layer registration, then voids. For IPC-6012 Class 3 the numbers are 25 um average and 20 um minimum at any point on the barrel, 5 um minimum at the knee, 50 um external and 25 um internal annular ring, and no voids. Class 2 moves those to 20 and 18 um. A report that gives one copper number per hole has answered one of the five questions.

The section is a destructive sample, so what it proves is a property of the coupon and the lot, not of the board in your hand. That is fine. The purpose of reading it is to catch a process that is drifting before it becomes a field return, and the way a thin wall hides inside a report is worth knowing before you approve one.

The five measurements, in the order that matters

FeatureClass 2Class 3Where to measure
Barrel copper, average20 um25 umtop, middle and bottom of the same barrel
Barrel copper, thin point18 um20 ummid barrel, where throwing power is worst
Knee thickness5 um5 umcorner where barrel meets the surface pad
Microvia plating12 um average12 um average, 10 um thincap and base of the blind via
Annular ring50 um external50 um external, 25 um internalfour sides, not the widest one
Plating voids1 per hole, under 5% of lengthnonefull barrel, both walls

The knee deserves its own line because it is the point that fails first in thermal cycling. Copper at the corner is always thinner than copper at mid barrel, the corner takes the highest strain when the laminate expands, and it is the one place where the section plane can miss the geometry entirely if the cut is a few micrometres off centre.

Why the section plane decides what you read

A microsection is only true at the plane where it was ground. IPC-TM-650 method 2.1.1 calls for the plane to land within 10% of the hole diameter from the true centre. On a 0.30 mm hole that is 0.03 mm of tolerance, and outside it the tool reads the chord instead of the diameter, which makes the barrel look thicker and the hole look smaller than it is. An off centre section is the most common way a 17 um wall is reported as 22 um.

Polishing media matters for the same reason. Alumina rounds edges and smears copper, and a smeared wall can bridge a real void or hide a thin spot. Diamond is the normal choice for Class 2 and Class 3 evaluation. If the report does not say what the sample was polished with and at what magnification the images were taken, the numbers inside it are still usable but the images are not evidence.

Then there is stress. Class 3 evaluation expects the sample to survive thermal stress before it is sectioned. A barrel that looks solid before a solder float and cracks after it is exactly the defect the requirement exists to catch, and a report with no stress step has skipped the part of the test that predicts field behaviour.

Three traps in a report that looks fine

One number per hole. An average with no location is not a measurement you can act on. Ask for three points per barrel and three barrels per coupon, with the coupon position on the panel. Copper throwing power varies from panel centre to edge, and the edge is where the plating is thinnest on many lines.

Annular ring measured at the widest side. Registration error is directional. On a four sided pad the ring can be 0.08 mm on one side and 0.02 mm on the opposite side, and quoting the best side turns a registration problem into a pass. The number that matters is the minimum, and the registration offset in the same report should agree with it.

A report with no traceability block. Coupon location, panel or lot reference, date, the IPC class it was judged against, and the revision of the standard. Without those four items nobody can tell whether the 25 um was measured on your lot or on a qualification panel from last year. SUPERB PCB issues slice reports with the lot and the class printed on them for this reason.

What we publish, so the report can be checked

Plated copper 20 um minimum in the barrel, 10 um maximum recess on a filled via, hole position tolerance 0.075 mm, layer to layer registration 0.025 to 0.06 mm, annular ring 3.5 mil on vias and 8 mil on component holes at 1 oz, aspect ratio 10:1 standard and 25:1 on the high layer line, 68 layers maximum, and a TDR coupon on every panel. Reports released with the lot: standard shipping report, slice report, impedance test report.

Those figures are on the PCB capability page and the process windows are on FR-4 process parameters. SUPERB Tech reads its own sections against the class on the purchase order rather than against a house number, because a 22 um average is a pass on Class 2 and a reject on Class 3. The reliability side of the same question is on high reliability PCB, and the plating arithmetic is in how thick the copper in a plated hole should be.

What to ask for with the next order

The IPC class in writing, the number of coupons and their position on the panel, whether the sample is stressed before sectioning, images at 200x and 500x with the polish media named, the minimum annular ring per side, and the registration offset as a number. Six items. With them a cross-section report becomes a process control document instead of a photograph of a hole.

Need a quote or a review of your stack against these limits? pcba@superb-tech.com · WhatsApp +86 133 9608 1443