One press cycle covers a 20-layer board built on through holes. Two to four cycles are needed once the stack carries blind or buried vias, because each set of buried layers has to be drilled, plated and bonded before the next layers go on. Our ceiling is seven cycles. The layer count sets the press program; the via structure sets the number of cycles.
Most buyers count layers when they ask this question. The layer count is the wrong input. A 20-layer through-hole board is a single book: inner cores imaged and etched, oxide treated, stacked with prepreg and copper foil, pressed once, then drilled and plated through the whole stack. A 6-layer board with two levels of buried vias can take three presses and more press time than the 20-layer board.
What one press cycle does to a panel
Inside the press the prepreg melts, flows into the copper topography, cures, and then cools. Two things move while that happens: the resin shrinks as it cures, and the copper and the glass do not shrink by the same amount. The panel that comes out is slightly smaller than the artwork that went in, and it is not smaller by the same amount in both axes.
The movement is small as a percentage and large as a distance. A laminate that shrinks 0.03% across a 520 mm panel moves 0.156 mm. Our published layer-to-layer registration window is 0.025 to 0.06 mm. Raw shrink is therefore between two and six times the registration budget, and the only reason a fine-pitch board works is that every layer is scaled before imaging, using a shrink factor measured on a test panel of the same construction and copper distribution.
That scale factor is per cycle. The second press does not shrink the book by the same amount as the first, because the ratio of cured core to flowing prepreg is different and the inner layers have already been through one thermal cycle. A shop that reuses one scale factor for every cycle is one reason a sequential build drifts out of registration on the outer layers.
The arithmetic that turns registration into pad size
Registration is not an abstract number. It is the space between the drill and the pad, and it is spent like this:
pad diameter = drill + 2 x (annular ring + registration)
Take a 0.20 mm via with the 3.5 mil (0.089 mm) ring we publish for a 1 oz inner layer. On a single-press board, where we allow 0.025 mm of registration, the pad works out at 0.428 mm. On a three-press stack, where the allowance has to grow to 0.06 mm, the same hole needs a 0.498 mm pad. Same drill, same current, 35% more pad area.
At 0.4 mm pitch that difference decides whether the via fits between the pads or has to move into the pad, and a via in the pad changes the assembly process. That is why press count belongs in the layout review and not only in the purchasing conversation: the number of presses sets the pad, the pad sets the pitch, and the pitch sets the escape routing.
Why the second press is not free
A press cycle is roughly 90 minutes at 200 degrees Celsius plus ramp and cool. Seven cycles put the inner layers through about ten and a half hours at temperature before the board is even drilled. Each pass advances the cure of the resin and oxidises the copper that has to bond again.
The sub-stack from the first press is fully cured when it goes back into the press. Prepreg added for the second cycle now has to bond to a cured surface rather than to a B-stage surface, which needs a different flow profile: enough flow to fill the copper topography and wet the cured resin, not so much that the dielectric collapses under the pressure. Using the first cycle's profile on the second cycle is how you get a void line at the interface or a dielectric that is thinner in the middle of the panel than at the edge.
There is also the scrap math. By the time a 20-layer book reaches the third press it carries the value of every inner layer already imaged, etched, inspected and bonded. One bad cycle throws away the whole book, not one layer.
Three things that go wrong
Counting layers instead of via levels. A 20-layer through-hole board and a 6-layer board with two buried via levels can need the same number of presses, or the 6-layer can need more. Ask the question as "how many via levels does this stack have" and the press count follows.
Spending the registration budget twice. A specification that asks for a 3.5 mil annular ring, a 0.4 mm pitch and a four-press stack is asking for three things that compete for the same 0.06 mm. Grow the pad, drop the ring, or move the via out of the pad. Pick one on the drawing instead of letting the shop pick for you.
Checking registration only at the end. Layer-to-layer registration can be measured on X-ray targets after every press. Checking after the final press tells you the board is bad when there is nothing left to do about it. Checking after cycle two lets you scrap the sub-stack before the expensive layers go on.
What SUPERB PCB keeps under control on a sequential build
Published limits on the multilayer line: up to 68 layers, up to seven press cycles, layer-to-layer registration 0.025 to 0.06 mm, annular ring 3.5 mil on a 1 oz via and 4.5 mil on 2 oz, hole position tolerance 0.075 mm, aspect ratio 10:1 on the standard line and up to 25:1 on the high-layer line, warpage 0.75% or better for assembly.
On a sequential build the X-ray target is read after each press, the shrink factor is re-measured per cycle, and the coupon stays on the panel so the same panel that carries the product carries the evidence. The stack itself is agreed before the first inner layer is imaged, because after that point the press count and the pad sizes are already fixed. The press side of that discussion is on our multilayer PCB page, the numbers are on the PCB capability page, and the HDI stack side is covered in 4-stage HDI via stacking. SUPERB PCB and SUPERB Tech run the same sequence on every order: scale, press, read the targets, then decide whether the next press goes ahead.
One honest limit: seven cycles is a process ceiling, not a recommendation. Above four presses the yield curve turns, and the cost of the extra cycles is usually better spent on a via structure that needs fewer of them.
What to send with the stack-up
Layer count, which layer pairs are blind or buried, the via span at each level, dielectric thickness per layer, target impedance and its tolerance, the annular ring the part needs, the finest BGA pitch, panel size, and final thickness with its tolerance. With those nine items the press count, the pad sizes and the registration budget can be fixed before the first panel is booked, instead of after the first X-ray.