Contact Us
  • Home
  • BLOG
  • How Many Reflow Cycles Can a PCB Survive?

How Many Reflow Cycles Can a PCB Survive?

For a dry FR-4 with a 150 C Tg and mid grade thermal performance, the practical limit is about 12 passes through a 260 C reflow before cohesive delamination becomes likely. A basic grade runs out at about 7, a high grade reaches about 20. The number is not a property of the resin name. It falls out of four values on the laminate datasheet, and it drops fast when the profile runs hot or the board goes into the oven wet.

A pass is any trip to soldering temperature. Two SMT reflows, one selective solder pass and one BGA replacement is four passes, not two.

The four datasheet numbers behind the count

FR-4 thermal grades are separated by decomposition temperature Td, the time to delamination at 260 and at 288 C, and z-axis expansion. A basic sheet sits near Td 310 C, T260 of 30 minutes, T288 of 5 minutes and 4 percent expansion, and it takes roughly 7 solder cycles. A mid grade sheet at Td 325 C, T260 of 50 minutes, T288 of 10 minutes and 3.5 percent expansion reaches about 12. A high grade at Td 340 C, T260 of 80 minutes, T288 of 15 minutes and 3 percent expansion reaches about 20.

The count assumes a dry board and the profile the material was qualified at. It is a statement about cohesive delamination inside the laminate, not about the copper. Vias keep their own schedule.

What one pass does to a board

From 25 C to a 260 C peak is 235 K. A 1.6 mm board with 3.5 percent z-axis expansion grows about 56 micrometres across its thickness. A copper barrel at 17 ppm per K grows about 6 micrometres over the same range. The 50 micrometre difference is absorbed as strain in the barrel wall and in the pad to barrel joint, once per pass, in both directions.

Moisture does the rest. FR-4 holds 0.2 to 0.3 percent water by weiw weeks in a normal store, and at 260 C that water becomes steam at a volume ratio in the hundreds. The steam has one place to go, which is into the resin. That is why a bake to J-STD-033 at 125 C before the first pass matters more than any single step later, and why baking after the first reflow cannot undo what the steam already did.

Via life is consumed faster than the cycle count suggests. A cost effective high Tg laminate that lasts 40 passes at 220 C lasts about 10 at 260 C, so a 260 C pass costs four times the via life of a 220 C one. Eight passes on a material with 4.6 percent expansion take roughly 37 percent of barrel life before the board meets a customer.

Where the count goes wrong in production

Counting reflow only. Selective soldering, wave soldering, touch up and every component replacement are passes. A build with three reflows, one selective pass and two reworks has spent six of its twelve before final test, and usually nobody wrote it down.

Ignoring copper mass. A panel with 6 oz inner layers carries far more heat into the laminate than a 1 oz one, so it stays above liquidus longer at the same peak. A profile that suits a 1.6 mm digital board will overcook a heavy copper power section. Copper weight belongs in the conversation about how many passes a board can take, not only in the price.

Re-running a profile after a fault. A board pulled out, reworked and run again has two passes for one assembly step. A board that was reflowed, reworked twice and reflowed again is at the edge of the count on a basic laminate. Track passes on the route card, per serial number, otherwise the number is a guess.

Reading T260 as a warranty on the assembly. T260 is a minimum sheet value measured on a clad coupon under a defined load. It says the material will not delaminate inside that test window. It says nothing about an assembly with its copper distribution and its vias taking a hot profile plus two reworks.

How SUPERB supports a build that sees several passes

SUPERB PCB works with laminates at Tg 130, 150 and 170 C, UL-94 V0, CTI at or above 175 V and dielectric breakdown at or above 4,000 V, up to 68 layers, up to seven lamination cycles, heavy copper to 6 oz inner and 10 oz outer, and 0.05 mm lines and spaces. The process window is published on FR-4 process parameters and summarised on PCB capability, with the power route on heavy copper PCB.

SUPERB Assembly runs a twelve zone nitrogen reflow below 500 ppm oxygen for SAC305, with 3D SPI before reflow, 3D AOI after it, and X-ray and CT to IPC-7095 holding voids under 5 percent on thermal pads. Moisture control is a 125 C bake to J-STD-033 with a lot record, dry pack for storage, and MSL floor life tracked on the line. High reliability work follows IPC-6012 and IPC-6018 on the high reliability PCB route.

Passes are recorded per serial number next to the profile, so an audit can see how much thermal exposure a board actually took rather than how much the traveller was supposed to allow.

What to send for a quote

Send the stackup and the laminate datasheet page with Tg, Td, T260, T288 and z-axis expansion, the number of soldering passes you expect including rework allowance, board thickness and copper weight, whether the assembly goes through selective or wave soldering, and the acceptance class. That is enough to say whether the material is a 7 pass part or a 20 pass part, and that answer changes the board price long before anything else does.

Need a quote or a review of your files against these criteria? pcba@superb-tech.com · WhatsApp +86 133 9608 1443