TPS82695SIPR
Product Specifications
TPS82695SIPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS82695SIPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS82695SIPR: a 2.5 V, 500 mA supply in a 2.3 mm package
The TPS82695SIPR is not a regulator in the usual sense. It is a complete step down converter module with the controller, the inductor and the input and output capacitors inside one MicroSiP package measuring 2.3 mm by 2.9 mm and 1.0 mm high. The output is 2.5 V at 500 mA, the switching frequency is 4 MHz, and the quiescent current in power save mode is 24 uA. A board that has no room for an inductor, and no appetite for a switching loop to qualify, gets a finished supply that needs no external component at all.
The family covers 2.5 V, 2.85 V and 2.9 V in the same body, and the 95 part is the 2.5 V member. Peak input current limit is 750 mA and the undervoltage lockout sits at 2.05 V falling, which suits a lithium cell that runs from 4.35 V down to 3 V. The package is a ball grid array at 0.4 mm pitch, so the land pattern and the stencil are the qualification rather than the electrical data.
Key electrical data for the 2.5 V module
| Input range | 2.5 V to 4.35 V recommended, with a 2.05 V undervoltage lockout |
| Output | 2.5 V fixed at 500 mA, with 2.85 V and 2.9 V siblings in the same body |
| Switching frequency | 4 MHz, which is what allows the inductor to sit inside the package |
| Quiescent current | 24 uA typical in power save mode, 4.5 uA in shutdown |
| Peak input limit | 750 mA, with a 15 mA limit under a shorted output |
| External parts | none required, which is the whole point of the module |
| Package | MicroSiP ball grid array, 2.30 mm by 2.90 mm, 1.00 mm profile |
Package, marking and reel data
| Body | MicroSiP SIP, 8 bump BGA at 0.4 mm pitch |
| Reel | 3000 pieces with the R suffix, 250 pieces with the T suffix |
| Assembly | open frame construction, handled like an 0805 part on standard surface mount equipment |
| Family status | the 2.5 V member is the released row, the 2.85 V and 2.9 V rows were preview at revision |
| Marking | printed on the package top, read at incoming inspection under a microscope |
Where a module beats a discrete converter
Hearables, medical patches, sensor tags, smart meters and any wearable with a 2.5 V rail are the natural fits. The argument is not only size. A discrete 4 MHz converter needs an inductor, two capacitors, a feedback network and a board area that has been checked for radiated emissions; the module carries the same silicon with the loop already closed inside the package, so the only thing left to get wrong is the land pattern.
The second argument is thermal and electrical repeatability. The inductor and the capacitors inside the module are characterised at the same time as the silicon, so the efficiency curve in the data sheet is the curve the customer gets, not a curve that depends on which inductor the assembler bought. For a product built in several factories, that removes a variable from every build. It also shortens the qualification: the module has one set of curves to review rather than a set per factory bill of materials. For a wearable that ships in three colours and two radio variants from the same board, that is the difference between one qualification and six. The same argument holds for the land pattern: one stencil, one reflow profile and one set of inspection points for every variant, which is where a five figure tooling bill usually hides.
Buyer questions on the TPS82695SIPR
Does the module need any external capacitor? No. The input and output capacitors and the inductor are inside the package, and the data sheet states that no additional component is required. A small input capacitor close to the pin is still good practice on a long input trace.
What is the difference between the R and T suffix? Packing only. The R suffix is 3000 pieces on a reel, the T suffix is 250 pieces for a prototype build, and the die and the marking are identical.
Can the output be changed to 2.85 V? Only by ordering the 2.85 V member of the same family, because the feedback is inside the module. That is the trade for having no external component: the output is fixed at the factory.
Buying this module through a component supplier
A module that cannot be substituted has to be planned rather than sourced on the day, because the family rows move in and out of release status. Our component lead time solutions page covers the buffer and the split shipment. For a wearable program that needs a second supply line, medical device components covers the traceability and change control those products expect.