Contact Us

TPS7B6850QPWPRQ1

Brand: Texas Instruments
Texas Instruments TPS7B6850QPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7B6850QPWPRQ1 — Power Management & Signal Chain | Superb Automation

TPS7B6850QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7B6850QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7B6850QPWPRQ1: a 5 V regulator with a watchdog built in

The TPS7B6850QPWPRQ1 is a 500 mA, 40 V automotive regulator with a fixed 5 V output and a window watchdog on the same die. In a vehicle the watchdog is what stops a crashed microcontroller from holding a motor driver or a display awake, and the rule is that it must not depend on the processor it supervises. Putting it inside the regulator means one less part to qualify, one less clock to route, and a fault output that a system can trust even when the processor is stuck.

The watchdog set is fully configurable in hardware. The WTS pin selects a window watchdog or a standard watchdog, the WRS pin sets the open to closed window ratio to 1:1 or 8:1, and the FSEL pin selects the oscillator range. A resistor from ROSC to ground sets the period: 20 kOhm with FSEL low gives a 10 ms window with a 2 ms tolerance band. The WD pin takes the service signal, WDO is an open drain fault output, and WD_EN disables the watchdog when the module is in a service mode.

Key electrical data for the 5 V watchdog part

Input range4 V to 40 V, with 45 V transients and operation during a cold crank
Output5.0 V fixed, 500 mA maximum, 500 mA of current limit typical
Quiescent current19 uA typical in sleep with the watchdog disabled, 29.6 uA with it running
Watchdog window10 ms typical at ROSC 20 kOhm and FSEL low, 9 ms to 11 ms across the tolerance band
Power gooddefault threshold 91.6 percent of the output, adjustable through the PGADJ pin
Reset and delayopen drain PG with a DELAY pin, and a WDO output for the watchdog fault
Protectioncurrent limit, thermal shutdown, and reverse current blocking through the pass element

Package, marking and reel data

BodyHTSSOP PWP, 28 pins, exposed pad, 37.8 C per W junction to ambient on a four layer board
Reel2000 pieces, large tape and reel
Finish and moistureNIPDAU, level 3, 260 C peak reflow, 168 hour floor life
Marking7B6850Q
GradeAEC-Q100 grade 1, junction range minus 40 to 150 C

Where a watchdog belongs inside the regulator

Instrument clusters, body control modules, head units and any module that can leave an actuator energised are the applications this part is built for. The pattern is always the same: a processor that must be supervised, a rail that must survive load dump, and a quiescent budget that a parked car imposes. The 19 uA sleep current with the watchdog disabled and 29.6 uA with it running are the numbers a battery drain calculation uses, and they are low enough that a module can stay connected for weeks.

The window watchdog is the harder of the two modes and the one that catches real faults. A standard watchdog only asks for a pulse inside a long period, so a processor stuck in a tight loop that toggles a pin can satisfy it forever. A window watchdog requires the pulse to arrive inside a narrow band, neither too early nor too late, which catches a runaway loop as well as a dead processor. The 1:1 and 8:1 ratio pins let the same part serve both a fast control loop and a slow supervisor task. The 2 ms tolerance band around a 10 ms window is wide enough for a scheduler that jitters, and narrow enough that a stuck loop cannot stay inside it by accident.

Buyer questions on the TPS7B6850QPWPRQ1

How is the watchdog period chosen? By the resistor from ROSC to ground, with the FSEL pin selecting the range. The period is independent of the load and of the input voltage, so a timer in software does not have to track it.

What happens when the watchdog is not serviced? The WDO open drain output pulls low and stays low until the fault is cleared. It can drive a reset line, a fault pin on a transceiver, or an input to the system basis chip.

Is the power-good threshold adjustable? Yes, the PGADJ pin shifts it, and the DELAY pin sets how long the PG output waits after the rail is in regulation. That lets a module hold the processor in reset until the clock is stable.

Buying this regulator through a component supplier

A 28 pin HTSSOP with a watchdog inside is a single source part on most approved lists, so the sourcing question is lead time and lot traceability rather than substitution. Our component lead time solutions page covers the buffer and the split shipment route. For the incoming check on a 2000 piece reel, incoming inspection plan sets out what to verify beyond the label.