TPS7A2118PQWDRBRQ1
Product Specifications
TPS7A2118PQWDRBRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7A2118PQWDRBRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7A2118PQWDRBRQ1: an automotive 1.8 V rail at 500 mA
The TPS7A2118PQWDRBRQ1 is the 1.8 V fixed output of the TPS7A21-Q1 family, an automotive regulator that sources 500 mA with 7.7 uV RMS of noise and 91 dB of rejection at 1 kHz. It is qualified to AEC-Q100 grade 1, which is minus 40 to plus 125 degrees ambient, and its junction rating extends to 150 degrees, so the temperature window is wider than the consumer families in the same range.
The order code carries several pieces of information. The 18 is the 1.8 V trim, the P marks the wettable flank body, the WDRB is the eight pin SON at 3.3 mm by 3.3 mm, and Q1 is the automotive qualification. The vendor lists 5000 pieces on a large reel for this body, half again the 3000 of a consumer part, and the marking is A2118P.
Key electrical data for the 1.8 V automotive point
| Input range | 2.0 V to 6.0 V, 2.2 V minimum for full regulation at 500 mA |
| Output current | 500 mA, with a current limit and thermal shutdown above the rating |
| Quiescent current | 6.5 uA typical, 18 uA maximum over the full automotive range |
| Accuracy | plus or minus 1 percent over temperature, tighter than the consumer members |
| Dropout at 500 mA | 355 mV in the 1.5 V to 2.5 V band, 265 mV at 2.5 V output and above |
| Rejection | 91 dB at 1 kHz, 71 dB at 10 kHz, 50 dB at 1 MHz |
| Noise | 7.7 uV RMS over 10 Hz to 100 kHz at 2.8 V output |
Package, marking and reel data
| Body | SON DRB, 8 pins, 3.3 mm by 3.3 mm, wettable flank |
| Reel | 5000 pieces, large tape and reel, 330 mm carrier, 12 mm tape |
| Finish | NIPDAU, moisture level 2 with a one year floor life |
| Marking | A2118P |
| Qualification | AEC-Q100 grade 1, minus 40 to 125 C ambient, 150 C junction |
Where an automotive 1.8 V rail belongs
Driver assistance cameras, radar front ends, telematics units and infotainment head units all need a quiet 1.8 V rail for their image sensor or their serializer, and all of them are supplied from a 5 V or a battery rail that carries load dump and switching noise. The 91 dB of rejection at 1 kHz is what makes a single linear stage enough, and the 1.8 V trim is the standard for the mobile industry processor interface lanes that connect the sensor to the processor.
The automotive part adds two requirements to the electrical ones. The wettable flank body allows an automated optical inspection of the solder joint, which most automotive lines require, and the wider temperature window means the regulator can sit near the image sensor in a housing that sees 105 degrees. The dissipation budget at 1.8 V is small: 500 mA from 2.2 V dissipates 200 mW, and the same current from a 5 V rail would dissipate 1.6 W, which is outside the package. The rail therefore has to follow a pre regulator.
Buyer questions on the automotive code
What does the P in the order code mean? It marks the wettable flank version of the SON body, which is the packing an automotive line needs for automated optical inspection. The same die ships in a plain SON without wettable flanks.
Why 5000 pieces rather than 3000 on the reel? That is the packing the vendor publishes for this body. Automotive programmes generally consume a full reel in a shift, so the larger packing is the normal order.
Is the 1 percent accuracy valid over the whole grade 1 range? Yes, and that is one of the differences from the consumer family, which specifies 1.5 percent. The tighter window matters where the rail is used as a reference rather than only as a supply.
Buying automotive regulators
Automotive parts carry traceability requirements that a consumer part does not, so the buying route is different. Sourcing audit trail sets out the documents we pass with a shipment, and supplier onboarding checklist covers the qualification we run before a new channel supplies a Q1 part.
The automotive grade adds three numbers to the consumer specification: 1 percent accuracy over temperature rather than 1.5 percent, a quiescent current maximum of 18 uA across the full range and a junction rating of 150 degrees. The output capacitor window of 1 uF to 200 uF is unusually wide, which allows a product to trade board area against load transient without changing the part. The wettable flank body allows automated optical inspection of the solder joint, and the marking A2118P carries the trim and the qualification in one string. The 5000 piece packing and the grade 1 window are the two facts that separate this code from the consumer family at the same trim. The reel size and the grade 1 window also decide how the part is bought, since a 5000 piece reel is the smallest order the vendor publishes for this body.