Contact Us

TPS7A2029PDQNR

Brand: Texas Instruments
Texas Instruments TPS7A2029PDQNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A2029PDQNR — Power Management & Signal Chain | Superb Automation

TPS7A2029PDQNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A2029PDQNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A2029PDQNR: a 2.9 V low noise rail in the 1 mm X2SON

The TPS7A2029PDQNR is the 2.9 V fixed output of the TPS7A20 family in the four pin X2SON body coded DQN at 1 mm by 1 mm. The 2.9 V trim is chosen when a circuit is specified at 3.0 V but has to keep working as the supply falls, or when a 3.3 V rail in the system is too high for the load. It delivers 300 mA with 140 mV of maximum dropout in the 2.5 V to 5.5 V band, so a 3.04 V input holds the rail at full load.

The family is the low noise branch of the TI linear line, and this part carries the same 7 uV RMS noise, 95 dB at 1 kHz and 1.5 percent tolerance as the 1.8 V members. The difference between choosing 2.9 V and 3.0 V is usually a matter of what the load is characterised at, and both trims exist in the same bodies.

Key electrical data for the 2.9 V point

Input range1.6 V to 6.0 V, 3.04 V minimum for full regulation at 300 mA
Output current300 mA, current limit 360 mA to 730 mA, short circuit 160 mA
Quiescent current6.5 uA typical, 10 uA maximum
Accuracyplus or minus 1.5 percent maximum over the full junction range
Dropout at 300 mA140 mV in the 2.5 V to 5.5 V band, 690 mV in the 0.8 V to 1.0 V band
Rejection95 dB at 1 kHz into 20 mA, 75 dB at 10 kHz, 60 dB at 100 kHz
Noise7 uV RMS over 10 Hz to 100 kHz, no bypass capacitor

Package, marking and reel data

BodyX2SON DQN, 4 pins, 1.0 mm by 1.0 mm
Reel3000 pieces, large tape and reel, 180 mm carrier, 8 mm tape
FinishNIPDAU
Moisturelevel 1, 260 C peak reflow
MarkingJI

Where a 2.9 V rail belongs

A 2.9 V rail is usually a sensor or a radio supply derived from a 3.3 V system bus, where the linear stage absorbs the difference and removes the switching noise. At 300 mA from 3.3 V the part dissipates 120 mW, which a 1 mm square body handles with a proper pad. In a battery product the same rail can run from a single cell down to 3.04 V, after which the output follows the battery instead of regulating.

Because the dropout in this band is 140 mV, the headroom requirement is modest and the efficiency at 3.3 V in is about 88 percent. That is often good enough to avoid a second switching stage, which is the real reason this class of part exists: one converter followed by a linear post regulator is cheaper and quieter than two converters, as long as the dissipation stays inside the package.

Buyer questions on the 2.9 V code

Is 2.9 V a standard trim? It is one of the fixed voltages the family publishes, alongside 1.8 V, 2.85 V and 3.0 V. It is chosen when a load is characterised at 3.0 V minus a small margin rather than at a round number.

Does the output capacitor value change with the output voltage? No. One microfarad of ceramic is the condition for the whole family, and the noise and rejection figures are quoted with that value at every trim.

What is the shutdown current? About 0.2 uA with the enable pin at ground. The smart pulldown holds the part off when the pin floats, so a missing resistor does not leave the rail enabled.

Buying a 2.9 V rail

Trims that are one step away from a round number are the ones most often dropped at end of life, because the demand for them is thinner than for 1.8 V or 3.3 V. Component obsolescence management explains how we track that risk, and one stop BOM sourcing covers buying a whole power tree rather than one line at a time.

At 2.9 V the rail is usually fed from a 3.3 V system bus, and the 140 mV dropout in the 2.5 V to 5.5 V band means the part regulates down to a 3.04 V source at 300 mA. The current limit window is 360 mA minimum, 520 mA typical and 730 mA maximum in this body, so a load that steps to 300 mA has margin over the minimum before the limit engages. Quiescent current is 6.5 uA typical and 10 uA maximum, and the smart pulldown holds the part off when the enable pin floats, which keeps a bring up sequence predictable. A 1 uF ceramic output capacitor is the stability condition for the family and the value used for the noise and rejection figures, so a larger value improves the transient but changes the loop response.