Contact Us

TPS76950QDBVRQ1

Brand: Texas Instruments
Texas Instruments TPS76950QDBVRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS76950QDBVRQ1 — Power Management & Signal Chain | Superb Automation

TPS76950QDBVRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS76950QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS76950QDBVRQ1 automotive 100 mA regulator with a 16 V input ceiling

The TPS76950QDBVRQ1 is the 5.0 V fixed member of the TPS769-Q1 family in the five pin SOT-23 body, rated at 100 mA with an input range that reaches 16 V on the current silicon. That ceiling is the reason the part exists: most small regulators stop at 6 V, so a rail fed from a 10 V or 12 V intermediate bus needs either a front end divider or a part like this one. AEC-Q100 grade 1 covers minus 40 to plus 125 degrees ambient, and the output tolerance on the current silicon is 1.2 per cent over load and temperature against 3 per cent on the legacy silicon.

Rejection is the other half of the story. The current silicon holds better than 70 dB at 1 kHz and 46 dB at 1 MHz, which is enough to keep the switching ripple of an upstream converter out of a sensor supply without an extra LC filter. The part also carries an internal soft start, so the inrush into the output capacitor is limited without an external capacitor on a control pin, which matters in a five pin body where there is no spare pin to put one on.

Key parameters printed in the SGLS118E document

Input range2.5 V to 16 V on the current silicon, 2.7 V to 10 V on the legacy silicon, 18 V absolute maximum
Output5.0 V fixed, with fixed members from 1.2 V to 5.0 V in the family
Load current100 mA
Accuracy1.2 per cent over load and temperature on the current silicon, 3 per cent on the legacy silicon
RejectionBetter than 70 dB at 1 kHz and 46 dB at 1 MHz on the current silicon
Quiescent current50 microamp typical at no load, 80 microamp maximum, 55 to 95 microamp at 100 mA
Soft startInternal, no external capacitor needed
ProtectionThermal shutdown and overcurrent limit

Package, reel and top side marking

PackageSOT-23, DBV body, five pins
Reel3000 pieces on a large tape and reel
Finish and moistureNickel palladium gold, moisture level 1, unlimited floor life
Temperature and markingMinus 40 to plus 125 degrees ambient, top side marking PCOQ

Where a 16 V input regulator earns its place

This is the regulator for a bias rail inside a module that already has a 12 V bus: gate drive for a silicon carbide stage, a reference for an amplifier, or the analogue supply of a sensor front end. The 16 V ceiling leaves room for the transients that a 12 V bus carries in a vehicle, which is exactly what the automotive qualification is there for. The 5 V fixed version is the one on most bills of materials because it feeds a CAN transceiver and a microcontroller at the same time, and 100 mA is enough for both when the transceiver is not driving a faulted bus. The CAN bus transceiver selection page covers the supply side of that pairing.

Where the rail has to survive a load dump or a reverse battery event, this part is the regulator and not the protection. It has no reverse polarity blocking of its own, so a series diode or a P channel switch in front of it is normal practice on an automotive input. The second point is the silicon generation: both are Active, the parts are not interchangeable on paper and the accuracy column differs by a factor of two, so a drawing that quotes 1.2 per cent has to name the generation or accept a wider band; the component obsolescence management page sets out how the two generations are tracked when a program runs across both.

Questions buyers ask before ordering

Can it run from a 12 V bus directly? Yes on the current silicon, which is rated to 16 V with an 18 V absolute maximum. The legacy silicon stops at 10 V, so the generation has to match the bus.

Is 100 mA enough for a CAN node? For the transceiver and the microcontroller yes, with headroom. A node that also drives a relay coil needs a separate path, because the coil inrush is well beyond the limit.

Does it need an output capacitor? Yes, a small ceramic close to the pin. The internal soft start limits the inrush, so the capacitor can be modest, but it cannot be omitted.

Ordering this part through SUPERB

SUPERB supplies this part against a bill of materials line, states which silicon generation the reel carries, and keeps the reel label with the certificate so the accuracy band in the drawing can be matched to the parts on the floor. Send the rail, the bus voltage and the target date through the component lead time solutions page and the answer comes back with the generation and the reel size.