Contact Us

SN65MLVD047PWR

Brand: Texas Instruments
Texas Instruments SN65MLVD047PWR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65MLVD047PWR — Power Management & Signal Chain | Superb Automation

SN65MLVD047PWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65MLVD047PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65MLVD047PWR: a quad M-LVDS driver for a doubly terminated backplane

The SN65MLVD047PWR is a quadruple multipoint LVDS driver. Its output current is raised above that of a standard LVDS driver so that it can drive a bus terminated at both ends, where the effective impedance falls to 30 ohm because the two terminations sit in parallel and the bus itself adds capacitance. That is the M-LVDS case, and it is the reason this part is not interchangeable with an ordinary quad LVDS driver.

Each driver supports data rates up to 200 Mbps and clock frequencies up to 100 MHz with controlled output transition times, which keeps stubs off the backbone from ringing. The part runs from 3.3 V, is characterised from minus 40 C to 85 C, and protects its bus pins to 9 kV of discharge. Multiple drivers may sit on the same bus, which is what makes a multipoint backplane with several line cards possible.

Key data for the SN65MLVD047PWR

FunctionFour M-LVDS drivers, one direction, for multipoint buses with several drivers present
Load30 ohm to 55 ohm, the range produced by terminating both ends of a backplane
RateUp to 200 Mbps data and up to 100 MHz clock
EdgesControlled output transition times so that stubs off the backbone do not ring
Protection9 kV ESD on all bus pins, high impedance when disabled
Supply3.3 V single rail, characterised from minus 40 C to 85 C

Body, marking and reel data

BodyTSSOP PW, 16 pins, with a 16 pin SOIC option in the same group
Reel2000 pieces on a large reel on the plain, .B and G4 rows
MarkingMLVD047 printed on the body
HandlingMoisture level 1, 260 C peak, unlimited floor life
TemperatureMinus 40 C to 85 C

Where multipoint signalling replaces a field bus

A telecom shelf with a clock and frame sync distributed from a control card to twelve line cards is the classic case. A point to point LVDS driver cannot feed that bus, because twelve loads in parallel plus two terminations present far less than 100 ohm and the swing collapses. The M-LVDS driver is rated for exactly that load, and its controlled edge keeps the reflections from the stubs from turning into double clocking.

The second case is a shorter reach replacement for an RS-485 bus inside a cabinet. The differential pair carries clock and data at 200 Mbps instead of a few megabits, and the connector and cable can be the same ones the older bus used. What changes is the receiver: M-LVDS receivers have a defined threshold behaviour for an idle bus, and an RS-485 receiver does not.

Board points that decide whether this part works

The first is the termination. Two resistors, one at each end, are required, and their value has to match the bus impedance rather than the 100 ohm of a point to point link. The second is the stub length. Controlled edges tolerate stubs, but only short ones, and a card cage with long backplane traces needs the length budget checked against the 200 Mbps rate.

The third is the number of active drivers. The standard allows several, but the protocol has to guarantee that only one talks at a time, and the enable timing has to be respected or two drivers will fight. The fourth is the failsafe behaviour, which for the driver side means the outputs must be disabled at power up until the controller is ready.

Multipoint drivers and the backplane they serve

A multipoint driver is bought against a shelf programme, so the quantity follows the number of line cards and not the number of shelves. Twelve cards per shelf and a hundred shelves is a thousand parts, which is half a reel, and that is the shape of most orders for this family.

The electrical question that decides the quote is the termination. A bus terminated at both ends presents 30 ohm to 55 ohm, and that is the range this driver is rated for. A customer who has terminated at one end only is better served by a point to point driver, and a customer who has put termination on every card has a bus that no driver can hold at 200 Mbps. We ask for the termination scheme before we confirm the row, because it is the one mistake that shows up only at full load.

Where the bus is being moved from RS-485 to a multipoint differential link, the interface selection background is on our bus transceiver selection page. Where the shelf is a long life telecom product, the availability planning is on our component lead time solutions page. A bus that carries a clock as well as data should be checked at the clock rate, not at the data rate, because the clock is the faster of the two.