Contact Us

SN65HVD74DR

Brand: Texas Instruments
Texas Instruments SN65HVD74DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

SN65HVD74DR — Power Management & Signal Chain | Superb Automation

SN65HVD74DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The SN65HVD74DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

SN65HVD74DR: a 20 Mbps full duplex 3.3 V RS-485 transceiver with no enable pins

The SN65HVD74DR is a full duplex RS-485 transceiver on a 3.3 V rail, rated to 20 Mbps, with separate driver and receiver pins and no enable pins at all. It is the always on member of the SN65HVD7x family: the driver is permanently enabled and the receiver permanently listening, which suits a point to point link or a bus where this node never has to release the pair.

The protection set is the strongest in the family: above 30 kV human body model, above 12 kV IEC 61000-4-2 contact discharge and above 4 kV of fast transient burst. The receiver hysteresis is 70 mV, the quiescent current is below 1.1 mA, and the standby figure on the members that have enables is 10 nA typical with under 5 uA maximum. The 1/8 unit load option allows 256 nodes on a segment.

Key data for the SN65HVD74DR

Duplex and rateFull duplex, up to 20 Mbps, against 400 kbps on the 70 and 71 members and 50 Mbps on the 76 and 77
EnablesNone on this member, so the driver and receiver are always active and no control line is needed
Loading1/8 unit load option, up to 256 nodes on the bus
ProtectionAbove 30 kV HBM, above 12 kV IEC 61000-4-2 contact, above 4 kV IEC 61000-4-4 burst, glitch free power up and down
Receiver70 mV of hysteresis for noise rejection, wide common mode window for long cable runs
CurrentBelow 1.1 mA quiescent in operation, standby 10 nA typical and under 5 uA maximum on the enabled members

Body, marking and reel data

BodyD, SOIC 8 at 4.90 mm by 3.91 mm, the small body for a full duplex pair
Reel2500 pieces on a large reel, carrier tape 12.5 mm, 330 mm reel
Tape noteThe tape table prints VSSOP DGS 10 against the SN65HVD74DR row even though the body is SOIC D 8, a labelling slip in the vendor file
HandlingMoisture level 1, 260 C peak on the rows that publish a level, so no bake before reflow
TemperatureMinus 40 C to 125 C on every row of the family

Where an always enabled full duplex part fits

Full duplex RS-485 between two boards inside an enclosure is a clean way to move a continuous stream in both directions: the master sends commands on one pair while the node returns samples on the other, and neither side has to arbitrate. Removing the enable pins removes the turnaround time and the software that manages it, which is why the 74 and 77 members exist.

The 20 Mbps rate covers most in cabinet links with room to spare. At that rate the cable length budget shrinks quickly, so the pair should be short and terminated at both ends with 120 ohm resistors. The 256 node capability is irrelevant on a two board link but matters when the same part is used on a multi drop segment in a different product. Termination is fixed by the pair rather than by the node count: 120 ohm at each physical end, and a short stub from the transceiver pins to the pair. Where the pair runs past several connectors, the impedance of each connector matters more than the transceiver choice at 20 Mbps.

Questions we get when this code is on a BOM

The first question is whether a part without enables can share a bus. It cannot: the driver is always on, so two nodes would fight. This part belongs on a dedicated pair per direction, and a shared half duplex bus needs the enabled members instead. We ask about the topology before quoting, because the wrong choice here costs a board spin.

The second question is about the difference between the 74 and the 76. Both are full duplex 3.3 V parts; the 74 stops at 20 Mbps and the 76 reaches 50 Mbps and carries enable pins. A build that has to switch between transmit and receive needs the 76, and a build that only needs a faster fixed link can move to the 77, which is the 50 Mbps member without enables.

How SUPERB supports this line item

We quote the SN65HVD74DR with the rate, the duplex and the enable question settled on the offer, and we hold the 20 Mbps and 50 Mbps members so a rate change stays inside one family. Customers comparing interface options for a new board can start from the CAN bus transceiver selection page, which also covers the RS-485 families we carry.

Where a link is being extended between cabinets and the cable loss becomes the limit, the component lead time solutions page describes how we present the available rows and date codes before a build schedule is fixed.