Contact Us

OPA330AID

Brand: Texas Instruments
Texas Instruments OPA330AID is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA330AID — Power Management & Signal Chain | Superb Automation

OPA330AID

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA330AID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA330AID: zero-drift CMOS operational amplifier with 50 microvolt offset and 35 microamps of supply current

OPA330AID is a zero-drift CMOS operational amplifier in an 8-pin SOIC that holds 50 microvolts of offset and 0.25 microvolts per degree of drift on 35 microamps in a SOIC body of 8 pins. The AID suffix is the 8-pin SOIC body, one of the three shapes the single is offered in alongside SC70 and a wafer level package. The amplifier uses an auto-calibration loop to hold offset to 8 microvolts typical and 50 microvolts maximum, drift to 0.02 microvolts per degree typical, and it does so on 35 microamps maximum from a 1.8 V to 5.5 V supply, with a 350 kHz gain bandwidth and 0.16 volts per microsecond of slew.

Order code and package

Order codeOPA330AID
Functionzero-drift CMOS operational amplifier, rail-to-rail input and output
PackageSOIC, 8 pins, body code D
Supply range1.8 V to 5.5 V
Supply current35 microamps maximum
Gain bandwidth350 kHz with a 100 picofarad load
Slew rate0.16 volts per microsecond at unity gain
Offset8 microvolts typical, 50 microvolts maximum
Drift0.02 microvolts per degree typical, 0.25 microvolts per degree maximum
Input bias current200 picoamps typical, 500 picoamps maximum at 25 C
Short-circuit current5 milliamps
DatasheetOPA330, OPA2330, OPA4330 family document, revision with reordered tables

Electrical parameters that decide the application

Offset over the full rangeheld by the auto-calibration loop rather than by a trim
Power-supply rejection1 microvolt per volt typical, 10 microvolts per volt maximum
Channel separation0.1 microvolts per volt at DC
Noise from 0.1 to 10 Hz1.1 microvolts peak to peak
Noise densitynear flat above the chopping frequency, with no 1/f corner in the published curve
Input common moderail to rail, with an input filter for radio frequency interference
Outputrail to rail, unity gain stable
Packages in the familyDSBGA, SC70 and VQFN for the single, SOIC for the dual and the quad
Operating rangeminus 40 to plus 125 C

Points to check before this part goes on a BOM

50 microvolts on a 5 V range is 0.04 of a bit on a 12 bit converter and 0.66 of a bit on a 16 bit one, which is the reason a zero-drift part is bought at all. The offset does not need a trim network, so the potentiometer, its tempco and the factory step that adjusts it all leave the BOM. On a 16 bit channel the remaining error is the reference and the resistor network rather than the amplifier.

0.25 microvolts per degree over the 165 degree range is 41 microvolts, which is smaller than the 50 microvolt room temperature limit. That is the property that separates a chopper from a trimmed bipolar part: the drift after calibration is not a fraction of the offset but a fraction of a fraction, so a channel calibrated once at 25 C holds inside a bit and a half at 16 bits over the whole range.

The auto-calibration loop moves the noise down in frequency rather than removing it. Between 0.1 Hz and 10 Hz the part produces 1.1 microvolts peak to peak, which on a 16 bit converter at 5 V is 7.2 bits of flicker. A DC channel that filters to 10 Hz therefore sees the chopper noise and not the 50 microvolt offset as its floor, and averaging for a second drops it by the square root of the number of samples.

35 microamps at 3.3 V is 115 microwatts, and 35 microamps over a year is 307 milliamp hours, which is within reach of a lithium coin cell. The 350 kHz gain bandwidth is the price: at a gain of 100 the closed loop corner is 3.5 kHz, and on a 1 V peak to peak signal the 0.16 volts per microsecond slew allows about 51 kHz, so at high gain the bandwidth is the limit and at low gain the slew rate is not.

Bias current of 500 picoamps maximum is small enough that a 1 megohm source adds 500 microvolts, ten times the offset, and a 100 kilohm source adds 50 microvolts, the same size as the offset. The crossover where the network starts to dominate is therefore about 100 kilohms, and a thermistor or bridge above that needs either a lower impedance divider or an input buffer.

Ten microvolts per volt of supply rejection is the number that limits operation next to a converter. A 100 millivolt ripple on the 3.3 V rail appears as 1 microvolt at the input, which is 20 percent of the offset, and the rejection is quoted as a DC figure. A board that puts this amplifier behind a switching regulator should still add a small series resistor and a capacitor on the supply pin, because the published rejection does not extend to the switching frequency.

Where this order code fits

Battery powered sensor nodes, handheld test equipment, temperature and pressure transmitters and low-side current sense stages use this part where the offset has to stay put over temperature without a calibration step. The integrated interference filter and rail-to-rail input make it workable next to a switching supply on the same board. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Is the OPA330 a chopper or an auto-zeroed amplifier? The datasheet describes a proprietary auto-calibration technique, which is a continuous loop rather than a sampled null. The observable result is 50 microvolts of offset with 0.25 microvolts per degree of drift and no 1/f corner in the noise curve.

Can this part be used on a 16 bit converter without calibration? The offset allows it, since 50 microvolts is 0.66 of a bit at 5 V. The flicker noise of 1.1 microvolts peak to peak from 0.1 to 10 Hz is 7.2 bits, so the usable resolution depends on how much averaging the channel can afford.

What is the source impedance limit? About 100 kilohms. At that resistance the 500 picoamp maximum bias current produces 50 microvolts, the same size as the offset, and anything above it makes the network the dominant error.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.