Contact Us

LM211MDREP

Brand: Texas Instruments
Texas Instruments LM211MDREP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM211MDREP — Power Management & Signal Chain | Superb Automation

LM211MDREP

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM211MDREP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM211MDREP: the enhanced product flow on the strobed comparator, minus 55 to plus 125

LM211MDREP is the enhanced product version of the single strobed comparator. The M in the code is the extended temperature grade and the EP suffix is the vendor's enhanced product flow, which buys a controlled baseline rather than a new die: one fabrication site, one assembly site, and a change notification before anything moves. The electrical rows are the ones the industrial LM211 already carries.

The part exists for a narrow but real gap. An industrial comparator stops at 85 degrees and an automotive comparator carries paperwork and a qualification report that a defence or medical programme may not want to fund. The enhanced product sits between the two: a wider temperature window, a frozen process, and a documented change control path, without the automotive submission package.

What an engineer has to check before using the code is the temperature range on the enhanced product addendum, because the EP flow is published separately from the standard document and the window is not always the one printed for the base part.

LM211MDREP as the vendor document publishes it

The electrical rows below are from the LM111, LM211 and LM311 document revision K dated March 2017, at plus or minus 15 volts, and they apply to the die that the enhanced product flow ships.

Channels1
Supply5 to 30 volts single, or plus or minus 15 volts split
Input offset voltage0.7 millivolts typical, 3 maximum at 25 degrees
Input offset voltage over temperature4 millivolts maximum on the base grade
Input offset current4 nanoamps typical, 10 maximum
Input bias current75 nanoamps typical, 100 maximum
Common mode rangeminus 14.5 to plus 13 volts on a plus or minus 15 supply
Large signal gain40 volts per millivolt minimum, 200 typical
Output low voltage0.75 volts typical, 1.5 maximum at 50 milliamps
Output leakage0.2 nanoamps at 25 degrees, 0.5 microamps over temperature
Supply current, positive rail5.1 milliamps typical, 6 maximum
Supply current, negative rail4.1 milliamps typical, 5 maximum
Response time, low to high115 nanoseconds
Response time, high to low165 nanoseconds
Output rating50 volts, 50 milliamps
Strobe3 to 5 milliamps, current driven, never shorted to ground
Offset balancetwo pins, external potentiometer
Temperature windowminus 55 to plus 125 degrees on the M grade, confirm on the EP addendum
Package8 pins, SOIC body D
Flowenhanced product, controlled baseline with change notification

What the enhanced product flow actually buys

A standard catalogue part can move between fabrication sites, change mould compound, or shift a test limit with a product change notice that a buyer has to notice in a document feed. The enhanced product flow narrows that: the baseline is fixed, the change notification comes to the customer directly, and a requalification is not triggered by a silent move.

For a board that has already been qualified by a customer, that matters more than a few millivolts of offset. A medical instrument that has a validated process and a defence programme that has a configuration baseline both treat a silicon move as a change they have to revalidate, and the cost of that revalidation is usually larger than the price difference between an industrial part and an enhanced one.

The flow does not include an automotive qualification report, an AEC-Q100 test summary or a PPAP. A programme that needs those documents needs the Q code, and the two are not interchangeable on paper even when they are the same die.

The minus 55 to plus 125 window, and what changes at the ends

At the cold end the input bias current falls and the offset stays inside its window, so a threshold that is correct at room temperature stays correct. At the hot end the offset current grows towards its 20 nanoamp ceiling, the output saturation rises towards its 1.5 volt maximum at 50 milliamps, and the supply current climbs to its 6 milliamp maximum on the positive rail.

The rows that matter over the whole window are the offset over temperature, the output saturation and the leakage current. A relay driver that works at 25 degrees with 0.75 volts of saturation has 0.75 volts of margin left at the hot end, which is usually enough, but a circuit that parallels two outputs to share current loses that margin quickly.

The common mode range also narrows with temperature in the same way as the quad family. On a plus or minus 15 volt supply the upper limit is 13 volts minimum at room temperature, and a signal that sits at 13.5 volts is inside the typical window and outside the guaranteed one. Divide it down or move the reference.

Strobe, balance and the pins that make this part unusual

The strobe is a current sink, not a voltage input. It needs 3 to 5 milliamps to force the output off, and the document warns twice that it must not be shorted to ground. A logic gate through a 1 kilo ohm resistor from a 5 volt rail gives 5 milliamps and is the safe way to drive it; a 10 kilo ohm resistor gives 0.5 milliamps and leaves the output in an undefined state.

The balance pins trim the offset at the calibration temperature. On an enhanced product part that is a slightly odd feature, because a frozen baseline is usually paired with a calibration step anyway, and the trim is what lets the calibration be a potentiometer rather than a software constant. In a sealed instrument the trim is set once and the pot is replaced by two fixed resistors selected at test.

Where the enhanced product comparator belongs

It belongs in instruments that are qualified once and built for a decade: a medical analyser front end, a defence power distribution board, an industrial controller with a validated threshold chain, a scientific instrument with a long service life. In each of those the qualification cost dominates the part cost, and the frozen baseline is the feature that is being bought.

It is the wrong part for a consumer product, where the industrial grade is cheaper and the temperature window is irrelevant, and for an automotive programme, where the Q code and its documentation are the requirement. The sourcing question is which flow is on the shelf, and our OEM procurement page covers how the flow is specified on a purchase order, while the component obsolescence management page covers what to do when the flow itself is discontinued.

Carrier and what to confirm before ordering

The EP flow is published on its own addendum, and the carrier rows there are the ones that apply. The base document prints the SOIC body in a 75 piece tube and on a 2500 piece reel, and those are the carriers this body supports, but the enhanced product rows should be read on the EP document rather than assumed from the base table.

LM211MDREPSOIC D, 8 pinsenhanced product addendumminus 55 to plus 125, controlled baseline
LM211DSOIC D, 8 pins75 pieces, tubeindustrial, minus 40 to plus 85
LM211QDSOIC D, 8 pins75 pieces, tubeautomotive, minus 40 to plus 125

Two checks belong on the purchase order. The temperature range has to be printed, because the M grade and the Q grade share a body and a pinout and differ on paper. The flow has to be printed as well, because a supplier that substitutes an industrial part for an enhanced one is making a change the programme has to revalidate.

Buying questions that come with this code

Is LM211MDREP a different die from LM211D? No. The die and the electrical rows are the same, and the difference is the temperature guarantee and the process control that comes with the enhanced flow.

Does the EP flow include an AEC-Q100 report? No. The automotive report belongs to the Q code, and a programme that needs it should not accept the EP part as a substitute.

What is the risk of using the industrial part instead? A silent process move that changes a limit, plus a narrower temperature window. For a product built for ten years, both risks are usually larger than the price difference.