ISO7340FCDWR
Product Specifications
ISO7340FCDWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7340FCDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7340FCDWR: four forward channels with filtered inputs
The ISO7340FCDWR is a four channel digital isolator with every channel forward, a low default state and an integrated noise filter on each input. It is the four channel member of the ISO734x group, which is rated to 3000 VRMS and 4242 VPK, one step above the 2500 VRMS family that shares the same footprint. The filter is the feature that separates it from a plain isolator: short spikes on the input are removed inside the part before they reach the barrier.
The F letter sets the default. On loss of input power or input signal, all four outputs go low. That is the state a gate drive or a relay command should take when the controller disappears, and it removes the need for a pull down network on the isolated side. The plain version holds the outputs high through the same event, which suits an active low enable that has to stay released.
Signalling rate is 25 Mbps. Propagation delay is around 20 ns typical with a maximum near 30 ns at 5 V, pulse width distortion is 2.5 ns typical, and common mode transient immunity is 25 kV per microsecond minimum and 70 kV per microsecond typical. Supply current in the DC state is 0.6 mA typical at 1 Mbps, and the surge rating reaches 7800 VPK, which is high for a body this size.
Key data for the ISO7340FCDWR
| Channels | Four, all forward, each with an integrated input noise filter |
| Data rate | 25 Mbps maximum specified |
| Isolation | 3000 VRMS for 60 s per UL 1577, 4242 VPK per VDE V 0884-10, surge 7800 VPK |
| Supply | 3.3 V or 5 V on each side, 3.3 V to 5 V level translation |
| Timing | Propagation delay about 20 ns typical and 30 ns maximum at 5 V, pulse width distortion 2.5 ns typical |
| Immunity | CMTI 25 kV per microsecond minimum and 70 kV per microsecond typical |
| Default state | Output low on loss of input power or input signal, the F variant |
Body, packing and marking data
| Body | SOIC DW, 16 pins, wide body |
| Packing | 2000 pieces on a 330 mm reel on the plain and the A row |
| Finish | NIPDAU, moisture level 2, 260 C peak reflow, one year floor life |
| Marking | The body prints the family and default code rather than the reel size, so the label decides the packing |
| Temperature | Minus 40 C to plus 125 C |
The filter, the delay and the test plan
A filter that removes short pulses also delays the edges that survive. On a 25 Mbps bus the added delay is small against the bit period, but on a handshake line where the receiver waits for a narrow acknowledge pulse the filter can swallow the pulse entirely. Check the shortest legitimate pulse on each of the four channels before this part is locked into a board.
The filter changes what a production test sees. A board with a marginal connector used to fail on intermittent spikes and now fails on a missing edge, which is a cleaner symptom but a later one. The test plan should therefore check edge timing on the first article, and the goods inwards check should confirm the marking and the date code rather than a functional pass alone. Our incoming inspection plan page sets out that check for barrier parts.
Where 3000 VRMS changes the choice
The four forward channels suit a parallel bus, a bank of relay commands or four chip selects crossing from a controller to a field connector. The 3000 VRMS rating and the 7800 VPK surge capability make the part usable where a 2500 VRMS device would need extra creepage on the board, and the wide body still fits the same 16 pin land pattern as the lower rated family.
Medical equipment uses the part on the mains referenced side of a monitor, where the barrier separates the patient circuit from the supply. Our medical device component sourcing page lists the certificates a reviewer expects to see, and the working voltage on the certificate is the number that has to be compared with the applied voltage, not the withstand rating.
Questions we get on this code
Buyers ask whether the 3000 VRMS part is a drop in for the 2500 VRMS family. The land pattern is the same and the pin map can be identical, but the certificates and the working voltage differ, so a safety file written around the lower rated part cannot simply swap in the higher one. The file has to name the new certificate.
The second question is about the default. The F letter is easy to miss on a purchase order, and the difference only shows up in a fault. Write the full string on the order, including the F, and compare the first article against the row in the packing table rather than against the shipping label alone.