ISO6521DR
Product Specifications
ISO6521DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO6521DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO6521DR: one channel out and one channel back, with a functional barrier
The ISO6521DR is the bidirectional member of the dual channel functional isolator family. One channel faces forward and one faces back, so a single eight pin part carries a request and a response across the same barrier. It uses the same double capacitive silicon dioxide insulation as its siblings, with functional isolation at 450 Vrms and 637 Vdc of working voltage and 2000 Vrms or 2828 Vdc of transient voltage for 60 seconds.
Each channel runs at 50 Mbps and propagates in 11 ns typical at 3.3 V, with about 1.8 mA per channel at 1 Mbps. The two sides may run from different rails inside the 1.71 V to 5.5 V window, so a 1.8 V processor and a 5 V interface can share the part without translators. The plain version drives its outputs high when the input side loses power, and the F version drives them low.
Key data for the ISO6521DR
| Channels | Two channels, one forward and one reverse, in an eight pin body |
| Rate | 50 Mbps per channel |
| Timing | 11 ns typical propagation delay at 3.3 V |
| Isolation | Functional class: 450 Vrms and 637 Vdc working, 2000 Vrms and 2828 Vdc transient for 60 s |
| Supplies | 1.71 V to 1.89 V and 2.25 V to 5.5 V rails, translation across 1.71 V to 5.5 V |
| Power | About 1.8 mA per channel at 1 Mbps at 3.3 V, 150 kV per microsecond typical CMTI |
Body, marking and reel data
| Body | SOIC D, 8 pins, 4.9 mm by 6.0 mm, with the leadless VSON option at 3.0 mm by 2.0 mm |
| Reel | 3000 pieces on a large reel on both body options |
| Marking | 6521, which distinguishes it from the 6521F row whose default output is low |
| Handling | Moisture level 2, 260 C peak, one year floor life |
| Temperature | Minus 40 C to 125 C |
The smallest honest isolator for a two wire link
A sensor with a request line and a data line, a relay driver with a command and a status return, and a serial port with transmit and receive are all two wire links. Each needs isolation in both directions but nothing more, and an eight pin part with one channel each way is the smallest device that does the job without a second package.
The rail flexibility is what makes it usable in mixed logic products. A modern processor runs at 1.8 V while the field side is still 5 V, and the part translates across that gap in both directions. Because each side has its own supply, the barrier also stops the 5 V side from back feeding the processor when the field supply is removed.
Points to confirm on the order
The first is the default state. This row drives high with the input unpowered, which is right for a signal that must read as active when a cable is pulled. A signal that must read as inactive needs the F row.
The second is the direction. A two channel part with both channels forward is the 6520, and using it for a bidirectional link leaves one direction unserved. The third is the barrier class: 450 Vrms functional is not a safety barrier, and a product whose protection relies on the barrier has to move to the higher rated families.
Two wire links and what the quote covers
This part is bought for links that carry one request and one response, so the quote usually covers the isolator and the two pull up or series resistors that the link needs. We ask for the direction of each signal and the default state that the system expects when the far side is unpowered, because those two answers select between the plain and the F rows.
The packing is 3000 pieces on a large reel for both bodies, which is more than most two wire link builds need. A partial reel with a recorded date code is the usual arrangement, and we keep the balance sealed so that the floor life clock stops between builds. For a module that ships in the thousands, the reel and the placement machine decide the schedule more than the part price does.
The fourth is the enable behaviour, which on this family is fixed rather than pinned, so a board that needs to tri state the outputs has to choose a different device. Where the link is part of an isolated measurement chain, the sourcing route is on our OEM procurement page. Where a short lead time is the deciding factor, the options are on our component lead time solutions page.The date code on that balance is the number to record, because a Level-2 part held past a year needs a bake and the bake is a line stoppage if nobody planned for it.