INA4180A3IPWR
Product Specifications
INA4180A3IPWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA4180A3IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA4180A3IPWR: the gain of one hundred member on the large reel
INA4180A3IPWR is the gain of one hundred member of the four channel current sense family in the fourteen pin TSSOP on the large reel. At 100 volts per volt a 1 milliohm shunt at 10 amps produces 1 volt, which is the combination most often used on a 24 volt rail where the shunt loss has to stay under 100 milliwatts.
The bandwidth at this gain is 150 kilohertz and the slew rate stays at 2 volts per microsecond, so a 20 kilohertz switching supply is well inside the small signal response while a 100 kilohertz loop already needs the lower gain. The offset at a 12 volt common mode is 500 microvolts maximum, which on a 10 millivolt sense signal is 5 per cent of reading before any calibration.
INA4180A3IPWR as the vendor document publishes it
| Channels | 4 |
| Gain options | 20, 50, 100 and 200 volts per volt, fixed by an internal network |
| Common mode range | 0.2 volts below ground to 26 volts |
| Supply | 2.7 to 5.5 volts |
| Offset at zero volts of common mode | plus or minus 25 microvolts typical, plus or minus 150 maximum |
| Offset at 12 volts of common mode | plus or minus 100 microvolts typical, plus or minus 500 maximum |
| Offset drift | 0.2 microvolts per degree typical, 1 maximum |
| Common mode rejection | 84 decibels minimum, 100 typical |
| Power supply rejection | 80 microvolts per volt |
| Gain error | 0.1 per cent typical, 1 per cent maximum |
| Gain error drift | 20 parts per million per degree |
| Nonlinearity | 0.01 per cent between 0.5 volts and half a volt below the supply |
| Bandwidth | 350, 210, 150 and 105 kilohertz for the four gains |
| Slew rate | 2 volts per microsecond |
| Voltage noise | 40 nanovolts per root hertz |
| Quiescent current | 900 microamps typical, 1 milliamp maximum for four channels |
| Temperature range | minus 40 to plus 125 degrees |
| Package | 14 pins, TSSOP body PW |
| Catalogue code | INA4180A3IPWR |
| Vendor status | active |
| Gain | 100 volts per volt |
| Carrier | large reel, R suffix |
| Package | 14 pins, TSSOP body PW |
Gain error of one per cent, and what it costs at ten millivolts
The gain error of INA4180A3IPWR is 0.1 per cent typical and 1 per cent maximum, with 20 parts per million per degree of drift and a nonlinearity of 0.01 per cent between 0.5 volts and half a volt below the supply. The power supply rejection is 80 microvolts per volt, so a 100 millivolt supply step moves the output by 8 microvolts referred to the input.
A one per cent gain error on a 10 millivolt sense signal is 100 microvolts, which is small against the 500 microvolt offset at a 12 volt common mode but larger than the offset at zero common mode. That ordering is why the family is specified with both common mode cases rather than one, and why a two point calibration at the working common mode recovers most of the error.
Four current sense channels in one fourteen pin TSSOP
INA4180A3IPWR is one quarter of the INAx180 family, a voltage output current sense amplifier with a fixed gain, packaged four to a fourteen pin TSSOP. The four gain options are 20, 50, 100 and 200 volts per volt, and the gain is set by a matched resistor network inside the package rather than by an external pair, so the gain error and the drift come from one trimmed block.
The common mode window runs from 0.2 volts below ground to 26 volts, independent of the 2.7 to 5.5 volt supply, which is what allows the part to sit on the high side of a 24 volt rail and still drive a converter that runs at 3.3 volts. All four channels share the supply pins but not the inputs, so four separate shunts can be read through one package.
Offset at zero volts of common mode, and again at twelve
The offset of INA4180A3IPWR is quoted twice, because the answer depends on where the inputs sit. At a common mode of zero volts the row reads plus or minus 25 microvolts typical and plus or minus 150 microvolts maximum. At a common mode of 12 volts the same row reads plus or minus 100 microvolts typical and plus or minus 500 microvolts maximum.
The drift is 0.2 microvolts per degree typical and 1 microvolt per degree maximum across the minus 40 to plus 125 degree range. On a 10 milliohm shunt at 5 amps the sense voltage is 50 millivolts, so 500 microvolts is one per cent of reading, and that is the number to put against the tolerance of the shunt itself before choosing a gain.
Three hundred and fifty kilohertz at a gain of twenty, and the three lower numbers
The bandwidth of INA4180A3IPWR falls as the gain rises, because the gain is set by the same internal network. The A1 device at a gain of 20 holds 350 kilohertz, the A2 at 50 holds 210 kilohertz, the A3 at 100 holds 150 kilohertz and the A4 at 200 holds 105 kilohertz, all measured at a 10 millivolt sense voltage.
The slew rate is 2 volts per microsecond on all four, and the voltage noise density is 40 nanovolts per root hertz. A 20 kilohertz switching supply measured through a 200 volts per volt channel therefore has five times the headroom it needs, while a 100 kilohertz current loop on the same channel is already at the edge of the small signal response.
Nine hundred microamps for four channels, and the carrier rows
The quiescent current of INA4180A3IPWR is 900 microamps typical and 1 milliamp maximum at 25 degrees, and it is quoted for the whole package rather than for one channel, because the four amplifiers share one bias block. Over the full temperature range the maximum rises to the same 1 milliamp figure, so the supply budget does not change with the ambient.
The package is the fourteen pin TSSOP, and the reel code carries the R suffix while the tube code carries a T. The body is the same one used by the dual and single members of the family, so the land pattern for four channels is the only one a board needs if the channel count may grow.
Where four current sense channels belong
INA4180A3IPWR belongs in a three phase motor drive, where three shunts read the phase currents and the fourth reads the bus return; in a quad hot swap card, where each rail has its own shunt; in a power over ethernet switch, where four ports are monitored through one package; and in a battery tester that cycles four cells at once.
The 26 volt common mode, the fixed gains and the 900 microamps are the three rows that fit those cases. What the part does not do is measure current in both directions, because the output is referred to ground rather than to a mid supply reference, and that is the difference between this family and the bidirectional one beside it.
What the four channels do not share
The four channels of this package share the supply pins, the bias block and the ground return, and they share nothing else. Each has its own input pair and its own output, so a fault on one shunt does not move the other three, and the four outputs can be read by four separate converter channels or by one multiplexed converter.
What they do share is the ground return current, and that is the coupling path a four channel part introduces where four single parts would not. The return from four outputs at 1 milliamp each is small, but the return from four shunts on the same copper is not, so the star point of the four shunt returns is the one place on the board that decides whether the channel to channel separation is real.
The gain against the shunt is a two variable problem and the offset is the constraint. Our amplifier cross reference page covers the gain options, and the incoming inspection plan page covers checking the shunt tolerance that sits beside it.
What shunt suits a gain of one hundred? On a 3.3 volt output range, a 1 milliohm shunt reaches full scale at 33 amps, and a 10 milliohm shunt reaches it at 3.3 amps. The shunt tolerance is then the dominant error, not the amplifier.
Does the offset change between the 20 and the 100 gain parts? No. The offset rows are the same on all four, quoted at the common mode rather than at the gain, so the input referred error does not improve with a higher gain.