Contact Us

INA381A1QDGSRQ1

Brand: Texas Instruments
Texas Instruments INA381A1QDGSRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA381A1QDGSRQ1 — Power Management & Signal Chain | Superb Automation

INA381A1QDGSRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA381A1QDGSRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA381A1QDGSRQ1: 26 V current sense with a 400 ns comparator for overcurrent protection

The INA381A1QDGSRQ1 is the automotive qualified, 20 V/V member of the INA381 family, a current sense amplifier with an integrated high speed comparator in a 10 pin VSSOP. Its common mode range is 0.2 V to 26 V, which is the range that covers a 24 V rail and the 12 V and 5 V rails below it, and the comparator gives an alert in 400 ns typical so a short circuit is caught before the switch that caused it is damaged.

The amplifier side is optimized for a 12 V rail: offset is 150 uV maximum at a zero common mode and 500 uV maximum at 12 V, with 1 uV per degree drift, gain error 1 per cent maximum at 25 C and 20 ppm per degree drift. The comparator has 50 mV of hysteresis, a threshold set by an external reference on the CMPREF pin, and two modes: transparent, where the alert follows the current, and latched, where the alert stays until the latch is reset.

Key data for the INA381A1QDGSRQ1

Gain20 V/V on the A1 code; A2, A3 and A4 are 50, 100 and 200 V/V in the same body
Common mode0.2 V to 26 V, independent of the 2.7 V to 5.5 V supply
Offset150 uV maximum at zero common mode and 500 uV maximum at 12 V common mode, with 1 uV per degree drift
Gain accuracy1 per cent maximum at 25 C with 20 ppm per degree drift
ComparatorOpen drain alert, 50 mV hysteresis, 400 ns typical propagation, standalone alert response under 2 microseconds, total system response under 10 microseconds
Supply2.7 V to 5.5 V single rail, 350 uA maximum supply current, minus 40 C to 125 C

Body, marking and reel data

BodyDGS, 10 pin VSSOP at 3.00 mm by 3.00 mm; the industrial family also ships an 8 pin WSON at 2 mm by 2 mm
GradeQ1 automotive suffix; the library document SBOS848B is the industrial revision, so the automotive release data comes from the Q1 document
ReelR suffix is the large reel, and the automotive packing list carries the date code and lot that the PPAP record refers to
PinsIN plus, IN minus, VS, GND, OUT, CMPIN, CMPREF, ALERT and RESET; the threshold is set by a divider into CMPREF rather than by an internal fixed reference
ModesTransparent or latched, selected by how the RESET pin is driven, so one part covers both a live current limit and a fault flag

Where 400 ns of comparator delay changes the protection budget

A short circuit on a 12 V rail through a 5 milliohm shunt develops a shunt voltage that rises faster than a controller sampling at 10 kHz can see. The INA381 puts the decision inside the amplifier: the output crosses the CMPREF threshold, the ALERT pin pulls down in 400 ns typical, and the switch driver can act before the current reaches its destructive peak. The whole chain from shunt to alert is under 10 microseconds, which is the number that decides whether a FET survives a hard short.

The 26 V ceiling is what fixes the application. It covers a 24 V nominal rail only while the rail stays at nominal, so a 24 V system that can ring to 30 V needs a divider or a higher voltage part. Below that ceiling the part is at home: 12 V server rails, 24 V industrial supplies, cordless tool packs and BLDC drivers. The offset specification is split by common mode because the input stage behaves differently near zero, and a low side shunt that sits at ground uses the 150 uV row rather than the 500 uV one.

The reference pin also allows the threshold to be proportional to a rail rather than fixed, which is how a protection limit follows a supply that is itself adjustable. That is a small detail with a large effect on a product that ships into several markets with different voltage settings. Our amplifier cross reference lists the parts with integrated comparators, and the one stop BOM sourcing note covers how a family of four gains is quoted as one line with a gain option rather than four.

Buyer questions on the INA381A1QDGSRQ1

Does the alert need a pull up? Yes, the output is open drain, so a resistor to the logic rail is required. The value sets the rise time, and with a 400 ns comparator a 10 k pull up into 10 pF gives a rise time that does not dominate the response.

Can the threshold be set below the amplifier offset? Not usefully. A threshold that sits within the offset window will trip at random, so the trip current should be at least ten times the current that the offset represents.

What is the difference between the VSSOP and the WSON body? The WSON is smaller and has no leads, which changes the thermal path and the inspection method. Electrically the two are the same die, and the pin count differs, so the footprint is not shared.

Availability and ordering notes

INA381A1QDGSRQ1 is the automotive 20 V/V member in the 10 pin VSSOP. The gain options are separate order codes, and the automotive release is a separate document from the industrial one in our library, so the qualification record has to come from the vendor. Because the trip threshold is set by two external resistors, a customer who changes the protection current needs a BOM change on those resistors and not a new amplifier, which is worth stating in a quotation for a product family with several current ratings.