INA310A1IDGKR
Product Specifications
INA310A1IDGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA310A1IDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA310A1IDGKR: current sense amplifier with an open drain comparator on the same die
The INA310A1IDGKR is the 20 V/V, A grade member of the INA310x family, a current sense amplifier with a common mode range of 4 V to 110 V and an open drain comparator with an internal 0.6 V reference built beside it. The point of the part is that the trip point is set by a resistor divider on the comparator input rather than by a second amplifier and a comparator on the board, so an overcurrent limit that used to take four parts takes one.
The A grade carries 0.15 per cent maximum gain error with 10 ppm per degree drift and 20 uV maximum offset with 0.25 uV per degree drift, against 0.5 per cent and 150 uV on the B grade. Bandwidth is 1.3 MHz with a 2.5 V per microsecond slew rate, so the amplifier side is fast enough that the comparator, not the amplifier, sets the response time. The comparator propagation delay is 1 microsecond typical and the output can latch, which turns a transient into a flag that survives until the host clears it.
Key data for the INA310A1IDGKR
| Gain | 20 V/V on the A1 code; 50, 100, 200 and 500 V/V are the other four members |
| Common mode | Minus 4 V to 110 V operational, minus 20 V to 120 V survival |
| Comparator | Open drain output with an internal 0.6 V reference, 1 microsecond typical propagation delay, 50 mV class of hysteresis, latching mode released by the RESET pin |
| Accuracy | A grade gain error 0.15 per cent maximum with 10 ppm per degree drift, offset 20 uV maximum with 0.25 uV per degree drift |
| Speed | 1.3 MHz bandwidth, 2.5 V per microsecond slew rate, 160 dB typical DC common mode rejection |
| Supply | 2.7 V to 20 V single rail, 1.6 mA quiescent, minus 40 C to 125 C |
Body, marking and reel data
| Body | DGK, 8 pin VSSOP at 3.00 mm by 3.00 mm |
| Reel | R suffix is the large reel; the VSSOP body is the only one this family ships in, so the footprint question is settled |
| Pins | IN plus, IN minus, VS, GND, OUT, CMPIN, CMPOUT and RESET; the comparator input is a separate pin from the amplifier output |
| Reference | Internal 0.6 V threshold on the comparator input, so the divider ratio is set by the trip current and not by an external reference part |
| Grade | A and B share the die, the body and the pinout; only the accuracy rows separate them |
Where an integrated comparator changes the board
The usual discrete overcurrent chain is a shunt amplifier, a comparator, a reference and a latch, four parts with four offsets that all drift. The INA310x reduces that to a divider into one pin, and because the amplifier and the comparator share a die, the offset of the amplifier is inside the loop that sets the trip point rather than beside it. At 20 V/V with a 1 milliohm shunt, a 20 A trip needs 400 mV at the amplifier output and therefore a divider that puts 0.6 V on the comparator input when the output is 400 mV, which is a two resistor ratio and nothing else.
The latching mode is what makes the part useful in a product that a technician services. In transparent mode the flag follows the current and disappears when the fault clears, so a scope is needed to see it. In latched mode the flag stays until the RESET pin is driven, so a controller that polls once a millisecond still sees a 10 microsecond event. Leaving RESET open or grounding it makes the comparator transparent, which is the default when a latch is not wanted. Where a customer is moving from a discrete chain, our amplifier cross reference lists the members with and without a comparator, and the medical device components note covers the same part in patient connected equipment, where a latched flag has to be cleared by a controlled reset rather than by a power cycle.
Buyer questions on the INA310A1IDGKR
Can the comparator trip point be changed at run time? Only by changing the divider, since the reference is fixed at 0.6 V inside the part. A digital trip point needs a comparator with an external reference or a digital monitor.
Does the comparator add to the amplifier offset? It adds its own input offset, which is not specified as tightly as the amplifier offset, so the trip point has a wider window than the measurement. Size the divider for the worst case trip, not the typical.
What is the advantage of 200 and 500 V/V members? A smaller shunt. At 500 V/V a 3 mV signal reaches 1.5 V, so a 0.1 milliohm shunt can be used at 30 A, which removes most of the shunt loss at the cost of a narrower input window.
Availability and ordering notes
INA310A1IDGKR is the A grade 20 V/V member in the 8 pin VSSOP. The Q1 automotive version of the A2 gain is a separate order code and a separate document, and the two should not be quoted as interchangeable on the strength of the shared body. Because this part is often specified as a functional replacement for a discrete chain, a customer evaluation usually needs the divider values as well as the part, and those follow from the trip current, the shunt and the gain.