Contact Us

INA240A1D

Brand: Texas Instruments
Texas Instruments INA240A1D is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA240A1D — Power Management & Signal Chain | Superb Automation

INA240A1D

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA240A1D from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA240A1D: 20 V/V current sense amplifier with enhanced PWM rejection in a 8-pin SOIC

INA240A1D is a bidirectional current shunt monitor built for inline motor current in a SOIC body of 8 pins. The INA240 exists for one job: measuring current in a phase leg where the common mode swings from below ground to the bus rail at the switching frequency. It holds 132 dB of rejection at DC and 93 dB at 50 kHz, over a common mode range of 4 V below ground to 80 V, and the A1 suffix fixes the gain at 20 V/V.

Order code and package

Order codeINA240A1D
Functionbidirectional current shunt monitor with PWM rejection
Gain20 V/V, set by the A1 suffix
PackageSOIC, 8 pins
Common mode4 V below ground to 80 V
Supply2.7 V to 5.5 V
Bandwidth400 kHz on all gain options
Settlingoutput settles to 0.5 percent of final value
Channelsone
Temperature rangeminus 40 to plus 125 C
Gain optionsA1 20, A2 50, A3 100, A4 200 V/V
DatasheetSBOS662 revision C, December 2021

Electrical parameters that decide the application

Offset voltage25 microvolts maximum
Offset drift250 nanovolts per C maximum
Gain error0.20 percent maximum
Gain drift2.5 ppm per C maximum
Common mode rejection132 dB at DC, 93 dB at 50 kHz
Quiescent current2.4 milliamps maximum
Outputvoltage output with a REF pin for bidirectional sensing
Slewset by the internal stage, not by the load capacitance alone
Input protectionthe inputs survive the phase node swinging below ground
Accuracy at 50 kHzthe AC rejection figure, not the DC one, sets the phase current error

Points to check before this part goes on a BOM

The 93 dB figure at 50 kHz is the number a motor drive should use. A drive switching at 20 kHz with 400 volt edges presents a common mode step the amplifier sees as a fast transient, and the DC rejection figure says nothing about how it recovers.

The common mode range starts 4 V below ground. That headroom is what lets the part sit on a low side shunt in a bridge leg without the body diode drop inverting the input during freewheel.

Gain error of 0.20 percent and gain drift of 2.5 ppm per C are the tightest in this family. The 400 kHz bandwidth is flat across all four gain options, so changing the gain option does not change the loop bandwidth the current controller was tuned against.

2.4 milliamps of quiescent current is real heat in a small package. Four of these on a three phase plus brake drive add about 10 milliamps to the low voltage rail, and the package temperature rise has to be checked against the 125 C limit.

The REF pin allows a bidirectional window, which a servo drive needs when the load regenerates. Driving REF from the same reference the ADC uses removes a term from the current reading, and driving it from a divider adds one.

The part does not filter the switching ripple for the host. A 400 kHz bandwidth passes the PWM harmonics that sit inside it, so the sampling instant and the software filter still have to be chosen against the switching frequency.

Where this order code fits

Three phase drives, servo amplifiers and solenoid controllers are the boards that need this part, and they usually arrive as a full driver plus shunt BOM rather than a single line. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Does the higher gain option reduce bandwidth? No. The 400 kHz bandwidth is quoted for all four gain options, which is unusual in this class and makes the gain choice a resolution decision rather than a speed one.

Can it be used on a low side shunt as well as inline? Yes. The common mode range covers both, from 4 V below ground to 80 V, so the same order code serves a ground referenced shunt and a phase node.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.