Contact Us

INA2180A3IDGKR

Brand: Texas Instruments
Texas Instruments INA2180A3IDGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2180A3IDGKR — Power Management & Signal Chain | Superb Automation

INA2180A3IDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2180A3IDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2180A3IDGKR: two 100 V/V channels in one VSSOP-8

The INA2180A3IDGKR is the dual channel member of the INA180 family at 100 V/V, in an 8 pin VSSOP body. Each channel reads a shunt from 0.2 V below ground to 26 V above it, runs from a 2.7 V to 5.5 V supply, and delivers 100 times the shunt drop as a voltage output. Offset is 150 uV maximum with the inputs at 0 V and 500 uV with them at 12 V, offset drift is 1 uV per degree, gain error is 1 percent maximum, and bandwidth at gain 100 is 150 kHz with a 10 pF load. The dual package draws 500 uA maximum against 260 uA for one channel.

Two channels in one body is a board space decision as much as a cost decision. A motor drive with a separate high side and low side measurement, or a two rail supply where both rails need watching, would otherwise need two amplifiers and two sets of decoupling. The INA2180 shares the supply pin and the bypass capacitor and keeps the two channels independent in the die. The A3 gain of 100 sits in the middle of the four options, between 50 and 200, and is the one that most often lands a 10 A rail inside a 3.3 V converter input.

Key data for the INA2180A3IDGKR

Gain100 V/V per channel, with 20, 50 and 200 available as A1, A2 and A4 in the same body
InputCommon mode minus 0.2 V to plus 26 V per channel, independent of the 2.7 V to 5.5 V supply
AccuracyOffset 150 uV maximum at 0 V common mode and 500 uV at 12 V, drift 1 uV per degree, gain error 1 percent
Bandwidth150 kHz at gain 100 with a 10 pF load, 355 kHz at gain 20 and 105 kHz at gain 200
Supply2.7 V to 5.5 V, 500 uA maximum for the dual package, 0.1 uF bypass at the supply pin
Slew rate2 V per microsecond, which is what a fast overcurrent detector actually needs

Body, marking and reel data

BodyDGK, VSSOP 8 pin, with the DSG WSON 8 pin as the other dual body in the same family
Reel3000 pieces on a large reel on the lettered rows, level 1 at 260 C with unlimited floor life
FinishNIPDAU on the lettered row, with the plain row printing Call TI for finish and moisture
Marking1D16 on the DGK row, four characters that identify the dual die and the gain
StatusThe plain row is printed against the WSON body, the lettered row carries the VSSOP body

Two channels, one bypass, two grounds

The failure mode of a dual monitor is shared impedance. Both channels refer to the same ground pin, so a high current in one channel's return path appears in the other channel's reading. On a motor drive this shows up as a current spike on the quiet channel at every switching edge. The fix is a star connection at the ground pin and separate return traces from the two shunts, and it is the first thing to check when a dual part behaves worse than two singles did.

The second question is bandwidth against gain. The A3 row at 150 kHz is fast enough for a 20 kHz current loop and the A4 row at 105 kHz is not, so the gain decision is also a loop bandwidth decision. Where a project is choosing between the dual and two single amplifiers, our amplifier cross reference lists the family by channel count, gain and body, and the BOM consolidation page covers how two line items become one without changing the current path.

Buyer questions on the INA2180A3IDGKR

Does the plain string ship the VSSOP body? The addendum prints the plain row against the WSON body with finish and moisture marked Call TI, and the active VSSOP row carries the letter. The order code and the reel label together are what confirm the body.

Can one channel be left unused? Yes, with its inputs tied to a defined potential. A floating input on an unused channel can swing the output and waste current, so the inputs are tied to the shunt node or to ground.

Why is the offset worse at 12 V common mode? The input divider network sees the common mode voltage and its mismatch grows with it. 500 uV at 12 V is still small against a 10 mV full scale signal, but it is four times the 0 V figure.

Availability and ordering notes

The VSSOP row is active at 3000 pieces on a large reel, NIPDAU, moisture level 1, marking 1D16. The plain string prints a WSON body with Call TI in the finish and moisture columns, so a bare string is not a safe order code. Both bodies are 8 pin but not the same land pattern. We confirm the body, the gain and the packing on the label, and the result is written into the sourcing audit trail.