Contact Us

INA190A2IDDFR

Brand: Texas Instruments
Texas Instruments INA190A2IDDFR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA190A2IDDFR — Power Management & Signal Chain | Superb Automation

INA190A2IDDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA190A2IDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA190A2IDDFR: the 50 V/V precision member on a large reel

INA190A2IDDFR is the 50 V/V member of the precision current sense family in the eight pin thin body on a 3000 piece large reel. It carries 132 dB of minimum rejection, 15 microvolts of maximum offset, 80 nanovolts per degree of offset drift and 100 nanoamps of maximum shutdown current, on the same 1.7 to 5.5 volt supply and the same minus 0.2 to plus 40 volt input window as the rest of the family.

Against the INA186 at the same gain the difference is the bottom of the range: 15 microvolts against 50 is the difference between resolving a tenth of full scale and resolving a quarter of it, and 0.3 per cent gain error against 1 per cent is the difference between a channel that can be specified to 1 per cent over temperature and one that cannot. The reference and enable pins are both present in this body.

INA190A2IDDFR as the vendor document publishes it

Gain50 V/V fixed
Gain error0.06 per cent typical, 0.3 per cent maximum
Gain error drift2 ppm per degree typical, 7 maximum
Nonlinearity0.01 per cent typical of full scale
Offset voltage3 microvolts typical, 15 microvolts maximum, referred to the input
Offset drift10 nanovolts per degree typical, 80 maximum
Input bias current0.5 nanoamps typical, 3 nanoamps maximum
Input offset current70 picoamps typical
Common mode rejection132 dB minimum, 150 typical, over minus 40 to plus 125 degrees
Power supply rejection1 microvolt per volt typical, 5 maximum
Reference rejection1 microvolt per volt typical, 6 maximum at this gain
Common mode rangeminus 0.2 volts to plus 40 volts, independent of the supply
Supply range1.7 volts to 5.5 volts
Quiescent current50 microamps typical, 65 maximum when enabled
Shutdown current100 nanoamps maximum
Bandwidth45 kHz at 25 V/V, 37 kHz at 100 V/V, 35 kHz at 500 V/V, intermediate options between those
Slew rate0.3 volts per microsecond
Settling to 1 per cent30 microseconds from a current step
Voltage noise densitypublished as a typical curve, no limit row
Swing to the positive rail20 millivolts typical, 40 maximum into 10 kohm
Swing to ground0.05 millivolts typical, 1 maximum
Zero current output1 millivolt typical at this gain, 3 maximum
Stable load capacitance1 nanofarad
Temperature rangeminus 40 to plus 125 degrees
Vendor statusactive, 3000 piece large reel
Catalogue codeINA190A2IDDFR
Vendor stringINA190A2IDDFR
BodySOT-23 thin, DDF, eight pin
Moisture levellevel 1, 260 degrees, no floor life limit
Directionbidirectional, reference pin available

The same architecture with the offset trimmed to fifteen microvolts

INA190A2IDDFR is the precision member of the same current sense family: 3 microvolts typical and 15 microvolts maximum of offset, with 10 and 80 nanovolts per degree of drift against the 50 microvolts and 0.5 microvolts per degree of the INA186. The bias current is the same 0.5 nanoamps typical, the supply window is the same 1.7 to 5.5 volts, and the common mode window is the same minus 0.2 to plus 40 volts.

What the tighter offset buys is range at the bottom. On a 10 milliohm shunt at a gain of 100, 15 microvolts of offset is 150 microamps of current error and 50 microvolts is 500 microamps, so a channel that has to resolve 1 amp from 1.1 amps needs the tighter part and a channel that has to resolve 10 from 11 does not. The price difference between the two families is the price of that bottom decade.

One hundred and thirty two decibels of rejection

Common mode rejection on INA190A2IDDFR is 132 dB minimum, twelve decibels better than the INA186, and the offset is quoted at 3 microvolts typical rather than at the 50 microvolt maximum of the cheaper part. On a 40 volt bus with 1 volt of switching ripple, 132 dB leaves 0.25 microvolts at the input, which is a sixth of the maximum offset and well under the noise of any bandwidth the part can pass.

The rejection is specified over the full minus 40 to plus 125 degree range rather than at room temperature, and that is the row a specification should carry. It is also the row that decides whether the monitor can sit on a phase node of a motor bridge with an 8 kHz chopper above it: at 132 dB the ripple is negligible, at 84 dB, which is what a cost optimised monitor publishes, the same ripple is 63 microvolts at the input and becomes visible on a small shunt.

Gain error that widens with the gain option

The gain error of INA190A2IDDFR is binned by option rather than published once: 0.04 per cent typical and 0.2 maximum at 25 V/V, 0.06 and 0.3 at 50, 100 and 200 V/V, and 0.08 and 0.4 at 500 V/V, with 2 and 7 ppm per degree of drift across the family.

That progression is not an accident of sorting. The same resistor network that sets 25 V/V sets 500 V/V, and the error of each element is multiplied by the gain it contributes to, so the highest gain carries the largest window. The practical consequence is that a 500 V/V channel bought for a 100 microvolt shunt drop has four times the gain error of the 25 V/V channel, and if the accuracy requirement is tight the answer is a larger shunt with a lower gain rather than the highest gain the part offers.

Fifty microamps running and one hundred nanoamps asleep

Quiescent current on INA190A2IDDFR is 50 microamps typical and 65 maximum over temperature, and the shutdown current is 100 nanoamps maximum, with the enable pin bringing the part back in the time the document prints rather than in a fixed interval. On a battery instrument that samples once a second, the difference between 50 microamps and 100 nanoamps is the difference between a week of standby and a month.

Two details decide whether the saving is real. The output has to be allowed to settle after the enable, so the sampling window must start late enough for the amplifier and the converter to both be ready. And the leakage into the enabled input has to be small next to the shunt current, otherwise the monitor measures its own wake up. The enable threshold is 0.7 times the supply on the SOT-23 body with 100 millivolts of hysteresis, so a slow ramp on the control line does not chatter.

Three bodies, and the reference pin only in two of them

INA190A2IDDFR comes in the SC70, the SOT-23 thin body and a ten pin UQFN, and the UQFN is the one that exists for a reason other than size: it carries both the reference and the enable pins with more separation between the input and the supply, which matters on a board with a switching node nearby. The SOT-23 also carries both pins, and the SC70 carries the reference without the enable.

All three are specified from minus 40 to plus 125 degrees, all three run from 1.7 volts, and all three share the electrical table, so a change of body is a change of footprint and moisture level rather than of performance. The moisture levels differ, and that is the row to print on the order: the small plastic bodies carry a floor life after the bag is opened while the large reel rows of some bodies are listed at level 1 with no limit.

Choosing between the INA186, the INA190 and the INA191

The three families share a topology and differ in one specification each. INA190A2IDDFR buys offset, 15 microvolts maximum against 50, and rejection, 132 dB against 120. The INA191 buys bias current, 100 picoamps against 500, in the smallest body of the three. The INA186 buys price and the wider choice of carriers, including the SC70 and the SOT-23 in both reel sizes.

The decision is therefore made by the error that dominates the channel. A microamp measurement through a large shunt is limited by bias and belongs to the INA191. A millamp measurement on a 40 volt bus is limited by rejection and belongs to this part. A channel where 1 per cent of full scale is good enough belongs to the INA186, and paying for the tighter grades there buys nothing the converter can see. Our amplifier cross reference page sets the three side by side, and the medical device components page covers the applications where the tighter offset is a requirement rather than an improvement.

The tighter offset is bought for a reason, so the reason belongs in the requirements. Our amplifier cross reference page covers the family comparison, and the incoming inspection plan covers the offset and gain check on the first article.

Is this part a drop in replacement for the INA186A2 in the same body? The footprint and the pinout match and the electrical window is tighter at every row, so it is a substitution upward; the check is that the reference divider and the converter range still suit the same gain.

Why is the gain error 0.3 per cent at this option rather than 0.2? The error of the internal network is multiplied by the gain, so the 50, 100 and 200 V/V options share one window and the 25 V/V option carries a tighter one.