Contact Us

DRV5056A6QDBZR

Brand: Texas Instruments
Texas Instruments DRV5056A6QDBZR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV5056A6QDBZR — Power Management & Signal Chain | Superb Automation

DRV5056A6QDBZR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV5056A6QDBZR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV5056A6QDBZR: a 100 mV per mT unipolar sensor for short travel

The DRV5056A6QDBZR is the higher sensitivity member of the DRV5056 unipolar family, at 100 mV per mT with a linear range of about 39 mT. Where the A3 option reads a 60 mT swing with room to spare, this one turns a 20 to 30 mT swing into a full output excursion, which is what a small magnet on a short travel mechanism produces.

The unipolar behaviour defines the range: the output starts at 0.6 V at zero field, rises with a south pole, and ignores a north pole entirely. The A in the code is the temperature compensated version, at 0.12 percent per degree, and the body is the SOT-23 on a 3000 piece reel.

Sensitivity and range always trade against each other in this family. The A1 option reaches 200 mV per mT over 20 mT, the A6 and A2 sit at 100 mV per mT over 39 mT, the A3 at 50 mV per mT over 79 mT, and the A8 at 66.6 mV per mT over 64 mT. Choosing between them is a matter of measuring the field at the working gap rather than of preferring one number.

Key data for the DRV5056A6QDBZR

OutputAnalog, ratiometric, 0.6 V at zero field, south pole increases it
Sensitivity100 mV per mT at 5 V typical on the A6 option
Linear rangeAbout 39 mT above the zero point
Quiescent output0.6 V nominal, 0.535 V to 0.665 V over the window
Compensation0.12 percent per degree, which tracks a magnet that weakens as it warms
Bandwidth20 kHz sensing bandwidth
Supply and current3.3 V or 5 V, 6 mA typical and 10 mA maximum

Body, packing and marking data

BodySOT-23, three pins, DBZ outline
Packing3000 pieces on a large reel on the R suffix
FinishTin lead finish, moisture level 2 at 260 C, one year floor life
Marking56A6 on the body, which separates it from the A2 and A8 dies

What the A letter does and the Z letter does not

The A6 and the Z1 are the two ends of the unipolar family. A6 is 100 mV per mT over 39 mT with compensation, Z1 is 200 mV per mT over 20 mT without it. A board that was qualified on A6 and swapped to Z1 will read twice as steeply and clip at half the field, which looks like a mechanical fault rather than a part substitution.

The compensation itself is a small deliberate error. The part raises its sensitivity as temperature rises so that the product of sensitivity and magnet field stays flat. That is correct when the magnet is a ferrite or a bonded material, and wrong when the field is generated by a coil or by a current in a conductor, because those do not weaken with temperature in the same way.

The addendum prints this string as an active row at 3000 pieces on a large reel with moisture level 2. The A revision row of the same string also appears, so a reorder should name the row rather than assume the plain string resolves to it.

Where the A6 sensitivity fits

Short travel actuators, small bore pneumatic and hydraulic valves, and handheld instruments where the magnet is a 3 mm disc at a 2 mm gap are the cases that need 100 mV per mT. The unipolar response also simplifies the mechanical arrangement, because only one face of the magnet has to be oriented.

Where the same board also carries an inertial sensor for motion, the IMU selection guide sets out which measurement belongs to which part, and the incoming inspection plan page covers the field test that catches a wrong sensitivity on a mixed reel.

Questions we get on this code

Does a 100 mV per mT part saturate on a strong magnet? It does, and the symptom is an output that stops rising while the mechanism keeps moving. The data sheet defines the linear range as 39 mT, above which the output approaches the rail and the reading no longer tracks the field.

Can the output drive a long cable? The part is built for a short analogue path, and a long unshielded run adds capacitance and pickup. A buffer at the receiving end, or a twisted pair with the return to the controller ground, keeps the 20 kHz bandwidth usable in practice.

A third question is about the zero. Because the quiescent window is plus or minus 10 percent around 0.6 V, two boards from the same batch will disagree at zero field by up to 130 mV, which at 100 mV per mT is more than a millimetre of apparent travel. Calibrate at power up, or accept the error knowingly.