Contact Us

BQ7695201PFBR

Brand: Texas Instruments
Texas Instruments BQ7695201PFBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ7695201PFBR — Power Management & Signal Chain | Superb Automation

BQ7695201PFBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ7695201PFBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ7695201PFBR: the 16 cell member of the same 48 pin family

The BQ7695201PFBR is a battery monitor and protector for packs of three to sixteen series cells. It shares the 48 pin TQFP body, the two converter arrangement and the high side charge pump drive with the ten cell member, so a product line that builds a 10S pack and a 16S pack can run the same board outline and the same test fixture, with only the configuration and the cell harness changing.

The measurement figures are the same class: coulomb counter input offset below 1 microvolt typical, cell voltage accuracy below 10 mV typical, and a plus or minus 200 mV current range across the sense resistor. Two independent converters allow current and voltage to be sampled at the same instant, which is what makes the impedance calculation meaningful on a pack with a moving load.

Protection covers voltage, temperature, current and short circuit, and the part also drives a secondary chemical fuse for the case where the FETs cannot open the fault. Two programmable regulators supply external loads, and the host interface is I2C, SPI or HDQ depending on the variant.

Key data for the BQ7695201PFBR

FunctionBattery monitor and protector with high side FET drive
Cell count3 to 16 series cells, Li-ion, lithium polymer and LiFePO4
ConvertersTwo independent converters, simultaneous current and voltage sampling
Current accuracyCoulomb counter input offset below 1 microvolt typical
Cell accuracyCell voltage measurement below 10 mV typical
Current rangePlus or minus 200 mV across the sense resistor
FET driveCharge pump driving high side N channel charge and discharge FETs, autonomous recovery option
ProtectionVoltage, temperature, current, short circuit, plus a secondary chemical fuse drive
RegulatorsTwo programmable LDO outputs for external system use
Interface400 kHz I2C, SPI, or HDQ single wire, selected by the variant
PackageTQFP, 48 pins
OrderingBQ7695201PFBR, 1000 pieces on a large tape and reel, moisture level 2 with a one year floor life

Where 16 cells changes the board rather than the part

Sixteen series cells puts the stack at 67 V at full charge. The part stands that off, but the board around it has to: the cell input pins carry the stacked voltage, the sense traces run past fifteen other cells, and the creepage between the top channels and the low side circuitry becomes a real constraint. A 10S board copied to a 16S pack without a creepage review will pass a bench test and fail a humidity test.

The second change is the cell harness. Sixteen cells means sixteen pairs of sense wires plus the thermistors, and the connector and the harness resistance become part of the measurement. A harness with a 0.1 ohm difference between two cell leads will show up as a voltage error only while the balancing current is flowing, which is the hardest kind of error to find after the pack is built.

The third change is the fuse and the FET choice. The pack current at 67 V is the same order as at 36 V, but the energy available in a fault is higher, and the FET has to be able to interrupt it at that voltage. The part drives the FET, it does not choose it.

The chemical fuse drive, and when it is the last line

The chemical fuse is a one time device. It is fitted for the case where the electronic path has failed: a FET that is shorted, a gate driver that no longer responds, or a current that is beyond what the FETs can interrupt. The part fires it with a controlled pulse, and the pack is then permanently open.

Because it is one time, the trigger conditions have to be agreed before the pack is released. A fuse that fires on a recoverable overcurrent turns a service call into a scrap pack. A fuse that never fires is dead weight on the bill of material. Getting that boundary right is a system decision that involves the pack owner, the safety case and the service policy, not just the configuration file.

The fuse also has to be matched to the drive. The part's pulse is sized for a class of fuse, and a fuse with a much higher firing energy will not open on that pulse. That is a datasheet check rather than an experiment, and it is one of the items that a second source fuse has to satisfy.

Where it fits in a build

Higher voltage packs where the ground reference and the protection independence both matter: battery backup units, light electric vehicles, e-bikes and e-scooters, non military drones, cordless equipment in the 48 V to 60 V class, and industrial packs above ten cells. A pack below ten cells is cheaper to build on the ten cell member of the same family.

The same 48 pin family is also where a programme often has to hold two cell counts for years, which makes the reel and the date code part of the plan. For a build that has to keep both variants in stock without over buying, the material requirements planning page covers how the two are planned together.

The sourcing side of this part is covered on the safety stock planning. For a programme that holds two cell counts at once, that page covers how the buffer is sized against the build plan.

Questions we get on this code

Can a 12S pack use this part? Yes, the cell count is a configuration item across the three to sixteen range, and the unused channels are tied off.

Does the high side drive need external components? The charge pump is inside the part, and the external items are the FETs and their gate resistors. The gate resistor value has to suit the FET, because too large a value turns the FET through its linear region slowly.

Is the 10 mV cell accuracy enough for balancing? It is enough to see a cell that is out of line, and not enough to certify a cell voltage to a millivolt. A pack that needs a tighter cell figure has to be checked with an external meter at the bench, not from the pack telemetry.

What is the difference between this part and the ten cell member? The cell count, and the creepage and harness work that goes with it. The package, the pin count and the register set are shared.