BQ32000DR
Product Specifications
BQ32000DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The BQ32000DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
BQ32000DR: real-time clock with trickle charger and automatic backup switchover
BQ32000DR is the timekeeper that keeps a timestamp alive across a power cut without a separate charger circuit in a SOIC body of 8 pins. The part keeps time from a 32.768 kHz crystal, switches to a backup supply automatically, and charges a capacitor or a rechargeable cell through an integrated trickle charger. Calibration is programmable from minus 63 to plus 126 ppm, the interface is I2C to 400 kHz, and an oscillator fail flag reports when the crystal has stopped.
Order code and package
| Order code | BQ32000DR |
| Function | real-time clock with backup switchover and trickle charger |
| Interface | I2C, up to 400 kHz |
| Crystal | 32.768 kHz, load capacitance selected by register |
| Calibration | minus 63 to plus 126 ppm, programmable |
| Backup | capacitor or non-rechargeable cell, automatic switchover |
| Charger | integrated trickle charger with selectable path |
| Flags | oscillator fail, stop bit, leap year compensation |
| Package | SOIC, 8 pins, 4.90 mm by 3.91 mm |
| Temperature range | minus 40 to plus 125 C |
| Supply | 2.0 to 3.6 V |
| Datasheet | SBAS467 revision C |
Electrical parameters that decide the application
| Calibration range | minus 63 to plus 126 ppm, asymmetric around zero, so a slow crystal has less correction room than a fast one |
| Calibration resolution | about 4.34 ppm per step with the standard register setting |
| Crystal load | a 12 pF crystal must not carry external load capacitors, since the part supplies the capacitance internally |
| Switchover | the main supply has to pulse before the part recognises a valid rail and hands back to it |
| Backup current | microamp class, which is what makes a 0.1 F capacitor good for days rather than hours |
| Time registers | updated once per second, all at the same instant, so a read cannot catch a half updated time |
| Leap year | compensated to 2100 in the register set |
| I2C | 400 kHz fast mode, so a 7-byte read fits in under 200 microseconds |
| Interrupt | the pin is a general purpose output or a frequency test output, selectable by register |
| Package thermal | 8-pin SOIC, so the crystal has to be placed close and away from switching nodes |
Points to check before this part goes on a BOM
Calibration runs from minus 63 to plus 126 ppm, which is not symmetric. A crystal that runs slow has only 63 ppm of correction available, so the crystal has to be specified on the fast side of nominal or the trim range runs out before the tolerance does.
A 12 pF crystal must not have external load capacitors on this part, because the load capacitance is internal and selected by register. Adding the capacitors that a bare oscillator needed pulls the frequency and moves the timekeeping error outside the trim range.
Sixty-three ppm is 5.4 seconds a day, and 126 ppm is 10.9 seconds a day. A month of uncorrected operation at the top of the range is over five minutes, which is why the trim has to be set at production and not left at the factory default.
The trickle charger is intended for a capacitor or a rechargeable cell, not for a primary cell. A non-rechargeable battery on a charger-enabled path is a leak and a safety question, and the charger has to be disabled in the register for that build.
Switchover needs the main rail to pulse before the part recognises it. A supply that ramps slowly through the threshold can leave the part on backup after the rail is valid, which shows up as a clock that is correct but running on the capacitor.
The registers update together once a second, which removes the classic read-across-the-second glitch. It does not remove the need to re-read after a rollover if the host reads the seconds register first and the date registers second.
Where this order code fits
Boards that need a timestamp but cannot afford a charger circuit are the ones that gain most from this part. Boards comparing it with a neighbouring part start from our One Stop BOM Sourcing page, and boards replacing a part that has gone end of life start from the OEM Procurement page.
Questions buyers ask
Can a non-rechargeable cell be used on the backup pin? Yes, provided the trickle charger is disabled. The charger is meant for a capacitor or a rechargeable cell.
How accurate is the clock without calibration? The crystal sets the accuracy; the trim range covers minus 63 to plus 126 ppm, which is 5.4 to 10.9 seconds a day at the extremes.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.