Contact Us

BQ298218RUGR

Brand: Texas Instruments
Texas Instruments BQ298218RUGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

BQ298218RUGR — Power Management & Signal Chain | Superb Automation

BQ298218RUGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The BQ298218RUGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

BQ298218RUGR: the same protection, with zero volt charging disabled

The BQ298218RUGR is a BQ2982 member of the single cell high side protection family, which means the FET driver, the sense arrangement and the CTR pin are the same as the BQ2980 parts and one function is deliberately removed: a deeply discharged cell is not revived through the protection FETs. On a pack where the charger must not bring a zero volt cell back up, that is the whole point of the code.

The family drives high side NFETs from a charge pump, measures current across a resistor as low as 1 milliohm, and protects on overvoltage, undervoltage, charge overcurrent, discharge overcurrent, short circuit and die temperature. The comparators are trimmed to plus or minus 1 mV on the two overcurrent functions and plus or minus 5 mV on the short circuit trip, which is what makes a 1 milliohm sense element usable.

The body is an 8 pin X2QFN with a 1.5 mm square die and a 1.69 mm land pattern, the supply current is 4 microamps in normal operation and 0.1 microamps maximum in shutdown, and the part is rated minus 40 to 85 C.

Key data for the BQ298218RUGR

FunctionSingle cell high side protection with an integrated charge pump FET driver
FamilyBQ2982, zero volt charging disabled
Overvoltage range in the family3.750 V to 5.200 V, trimmed per code
Undervoltage range in the family2.200 V to 3.000 V, trimmed per code
Charge overcurrent rangeMinus 4 mV to minus 64 mV, accuracy plus or minus 1 mV
Discharge overcurrent range4 mV to 64 mV, accuracy plus or minus 1 mV
Short circuit range10 mV to 200 mV, 250 microsecond delay, accuracy plus or minus 5 mV
Temperature protectionFixed trip at 75 C or 85 C depending on the code, plus CTR
Sense resistorDown to 1 milliohm
Supply current4 microamps normal, 0.1 microamps maximum in shutdown
PackageX2QFN, 8 pins, 1.5 mm square body, 1.69 mm land pattern
Ordering3000 pieces on a large tape and reel on the .A row, marking 82

Why a product would turn zero volt charging off

Zero volt charging lets a charger push a small current into a cell whose voltage has collapsed, in the hope that it recovers. On a consumer product that is a convenience: a pack left in a drawer for a year can often be brought back. On a pack where a collapsed cell means the cell has been damaged, the same function is a hazard, because it puts energy into a cell that should be replaced.

The BQ2982 members disable the route, so a cell below the undervoltage threshold stays disconnected. The product then reports a dead pack rather than attempting a recovery. For medical devices, tools that are serviced rather than repaired, and any pack with a service procedure for a flat cell, that is the right behaviour.

The decision is a policy one and it belongs in the pack specification. It is not a performance difference, and a customer who asks for the 218 because it is newer has probably not looked at the function that was removed.

Reading this code against the family grid

The comparison table for the family is a grid, and the text extract from the document shifts the columns, so the row that carries this code does not line up cleanly in a text dump. What the table does show is the range each column can take, and that the BQ298218 sits inside it with the zero volt charging column marked disabled. For a purchase order, the reliable record is the addendum plus a confirmation from the vendor on the trimmed values for this code.

The addendum itself has an oddity worth noting: the plain BQ298218RUGR row prints no status and no quantity in the extract, while the .A row prints active, production, 3000 pieces on a large tape and reel with marking 82. Treat the .A row as the confirmed one and ask the distributor to confirm which row it is quoting.

Where it fits in a build

Single cell packs where a flat cell must be treated as a fault: medical handhelds, serviceable tool packs, and instruments with a documented battery replacement. The high side arrangement keeps the pack ground stable, which matters on any product that measures the cell from the system ground.

For a programme that is holding buffer stock of this part against a long production run, the safety stock planning page covers how we size the buffer and what we do when the vendor changes a row.

The sourcing side of this part is covered on the component obsolescence management. For a pack that will be serviced for years, that page covers the alternates we qualify before a row changes.

Questions we get on this code

Does disabling zero volt charging affect normal charging? No. A cell above the undervoltage threshold charges normally. The difference only appears when a cell has collapsed below it.

Is the overtemperature trip fixed? It is fixed per code at 75 C or 85 C. The CTR pin is separate and can take an external thermistor for the FETs.

Can the part be used with a 2 milliohm sense resistor? Yes, and the current trip points then halve for the same millivolt setting. The accuracy in millivolts stays the same, so the percentage accuracy improves.

What should be checked at incoming inspection? The marking, the reel size and the orderable string. The 82 marking belongs to the .A row, and a plain row that shows something else is a different reel.