Contact Us

VBL1402

Brand: VBsemi
VBsemi VBL1402 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL1402 — Discrete & Power Semiconductors | Superb Automation

VBL1402

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL1402 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL1402: 40 V and 150 A at 2 milliohm

The VBL1402 is a single N channel MOSFET in a TO263 body rated at 40 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 150 A of drain current, 3 milliohm at a 4.5 V gate and 2 milliohm at a 10 V gate. It sits between the 30 V part in this family and the 60 V parts, and its resistance is close to the bottom of the band.

Forty volts is the class used on a 24 V rail with transients, on a 36 V battery string and on a 24 V automotive rail that does not see a full load dump. At the 80 per cent rule the part works to 32 V continuously, which covers a 24 V pack at 28.8 V and does not cover a 36 V pack at the top of charge.

At 2 milliohm the loss at 60 A is 7.2 W and at the printed 150 A it is 45 W. As with the rest of this band, the die figure and the thermal figure are far apart, and the package decides where the usable current sits.

Key data for the VBL1402

ConfigurationSingle N channel
PackageTO263, surface mount, tab soldered to the board
VDS40 V
VGSPlus or minus 20 V
Vth3 V typical
ID150 A, a die figure at a 25 C case
RDS(on) at 4.5 V3 milliohm
RDS(on) at 10 V2 milliohm
TechnologyTrench
Loss at 20 A0.8 W at 2 milliohm
Loss at 60 A7.2 W at 2 milliohm
Thermal pathTab to copper, no isolated substrate

Thirty two volts of working ceiling on a twenty four volt rail

A 24 V lead acid pack at the top of charge is 28.8 V and a 24 V lithium pack is about 29.4 V. Both are inside 32 V, so the part works, and neither leaves much room. A disconnect that opens under load puts the pack inductance into the drain node and the peak passes 32 V for a short time.

The clamp is the answer, and at 40 V there is not a lot of room for the clamp voltage either. A suppressor that clamps at 36 V leaves 4 V of headroom at the drain, which is inside the absolute rating and outside the derated ceiling. That is a working compromise as long as the clamp energy is inside the suppressor rating.

For a 36 V pack the top of charge is 42 V, which exceeds the absolute rating. The 60 V class is the correct choice for that rail, and the resistance penalty is a milliohm or two, which is small against a destroyed part.

Two milliohms at a hundred and fifty amps

At 2 milliohm the die is large and the loss at high current is still significant. At 60 A the loss is 7.2 W and a TO263 tab on a good pad passes it. At 100 A it is 20 W and the cooling has to be deliberate. At 150 A it is 45 W, which is a heatsink and not a pad.

The gate drive at 10 V gives the 2 milliohm figure. At 4.5 V the resistance is 3 milliohm, a 50 per cent increase, and the loss rises with it. On a 100 A load that is 10 W against 20 W, which is the difference between a pad and a heatsink.

The 3 V threshold means a 5 V driver has only 2 V of overdrive, so the 4.5 V column is the one that applies rather than the 10 V one. That is worth saying plainly: a board driven at 10 V gets 2 milliohm, and one driven at 5 V gets 3.

On a 24 V automotive rail the standard transient is higher than the steady state by a wide margin, and a 40 V part relies on the clamp network to keep the drain inside its window. Where the product claims a load dump rating, the clamp has to be sized for the energy the standard defines, and the part is then chosen for its behaviour during the clamp rather than for its resistance at 20 A.

Where the part fits and where it does not

It fits a battery disconnect on a 24 V pack, a motor drive on a 24 V system, a high current load switch, an ORing element on a 24 V bus and a synchronous rectifier on a low voltage output. It does not fit a 36 V pack at the top of charge, and it does not fit a continuous load above about 60 A without a real thermal solution.

For a 24 V pack the deciding parameters are the clamp voltage and the gate voltage the driver supplies. Our material requirements planning page covers how a part used across several products is planned against the build schedule.

The sourcing side of this part is covered on the component shortage forecast. For a part used across several builds, that page covers how a shortage is seen before it stops a line.

Questions we get on this code

Is 40 V enough for a 24 V pack? It covers 29.4 V with room for a clamped transient. Without a clamp the margin is thin, and a 36 V pack is out of range entirely.

Does 2 milliohm hold at 5 V gate drive? No. It is a 10 V figure, and the 4.5 V column is 3 milliohm, which is what a 5 V driver delivers.

Can it carry 150 A? The die can at a 25 C case. At 45 W the tab cannot, so the working continuous figure is nearer 50 to 60 A on a good pad.

What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.