VBL1141N
Product Specifications
VBL1141N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL1141N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL1141N: 140 V and 100 A in TO263
The VBL1141N is a single N channel MOSFET in a TO263 body rated at 140 V drain to source, plus or minus 20 V on the gate, a 3.2 V threshold, 100 A of drain current and 11 milliohm at a 10 V gate. The catalogue page prints the resistance at a 10 V gate only.
One hundred and forty volts is a class that sits between the 100 V parts used on 48 V systems and the 200 V parts used on 110 V systems. It covers a 96 V battery pack at 100 per cent of charge, a 110 V DC bus with a clamp, and a rectified 110 V AC rail only after a step down. It is the class chosen where a 100 V part has too little margin and a 200 V part costs more resistance than the budget can afford.
At 11 milliohm the loss at 40 A is 17.6 W and at 100 A it is 110 W. The first figure a TO263 tab passes with a good copper area. The second does not exist in a surface mount body, so the current column is again a die figure.
Key data for the VBL1141N
| Configuration | Single N channel |
| Package | TO263, surface mount, tab soldered to the board |
| VDS | 140 V |
| VGS | Plus or minus 20 V |
| Vth | 3.2 V typical |
| ID | 100 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 11 milliohm |
| RDS(on) at 4.5 V | Not printed on the catalogue page |
| Technology | Trench |
| Loss at 10 A | 1.1 W at 11 milliohm |
| Loss at 40 A | 17.6 W at 11 milliohm |
| Thermal path | Tab to copper, no isolated substrate |
One hundred and forty volts on a ninety six volt pack
A 96 V lithium pack reaches about 110 V at full charge, and the 80 per cent derating rule puts this part at 112 V, which is right at the top of charge with nothing left for a transient. That is tight. A pack that can be disconnected under load puts its cable inductance into the drain node, and the peak passes the top of charge for tens of nanoseconds.
The answer is either a clamp at the switch or the 200 V class. A transient suppressor across the drain and source, close to the part, is the cheaper route and it works as long as the energy is inside the suppressor rating. Where the load is a large inductive machine, the energy is large and the 200 V part is the honest choice.
On a 110 V DC bus the margin is 30 V, which is comfortable for a clamped rail and not for an unclamped one. On a rectified 110 V AC rail at 155 V the part is inside its absolute rating but outside the derated ceiling, so it is not a fit.
Getting eleven milliohms out of the die
Eleven milliohms at 140 V is a large die for the voltage class. The area goes into both withstand and conductance, and the package has to remove the loss, which at 40 A is 17.6 W. That is a copper and airflow problem rather than a silicon one, and it is why the pad geometry matters more than the part number in this range.
The gate drive has to reach 10 V to get the printed figure. With a 3.2 V threshold, a 5 V gate has under 2 V of overdrive and the resistance rises. On a converter with a 12 V rail, a gate resistor of a few ohms and a diode for turn off gives a transition fast enough for 100 kHz.
The switching loss at this die size is significant and the gate charge is not published. For a hard switched converter at 50 kHz the conduction loss at 40 A is 17.6 W and the switching loss can be of the same order. At 100 kHz the switching term dominates. Ask for the curve before the frequency is fixed.
Measuring the resistance on a sample is worth the afternoon it takes. A four wire measurement at 40 A with the gate held at 10 V and the case at a known temperature gives the number the board will see, and it separates a die that meets its published figure from one that is at the edge of a lot. On a part at 11 milliohm the test leads contribute more than the die, so the four wire arrangement is not a formality.
Where the part fits and where it does not
It fits a motor drive on a 96 V pack, an inverter stage on a 110 V DC bus, a solar input switch, an electric vehicle charging pile stage and a power module where the current is shared between several dies. It does not fit a 220 V AC derived rail, and it does not fit a continuous 100 A load in a surface mount body.
For a 96 V pack the deciding parameters are the transient the pack can deliver and the clamp that limits it. Our strategic sourcing page covers how a part at this class is kept on a single approval across several products.
The sourcing side of this part is covered on the supplier scorecard. For a part bought in volume, that page covers what is measured on the source over a quarter.
Questions we get on this code
Is 140 V enough for a 96 V pack? At the top of charge it is 110 V, which leaves 30 V and puts the part right at the derated ceiling. With a clamp it works; without one the 200 V class is safer.
Can it carry 100 A? The die can at a 25 C case. At 110 W of loss the tab cannot, so the practical continuous figure is well under half of that.
Is the resistance valid at 5 V? No. It is a 10 V figure, and the page does not print a 4.5 V column.
What should a purchase order carry? Part number, TO263, and the packing the line can take. We confirm the reel quantity on the offer.