Contact Us

VBGP1802

Brand: VBsemi
VBsemi VBGP1802 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGP1802 — Discrete & Power Semiconductors | Superb Automation

VBGP1802

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGP1802 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGP1802: 2.1 milliohm at 80 V in a TO247 body

The VBGP1802 is a single N channel MOSFET in a TO247 body, rated at 80 V drain to source, plus or minus 20 V on the gate, a 3.5 V threshold, 250 A of drain current and 2.1 milliohm at a 10 V gate. It is one of the lowest resistance 80 V parts in a through hole body, and that changes which part of the circuit is the problem.

At 2.1 milliohm the die is no longer the dominant resistance in most circuits. A copper trace 10 mm long and 5 mm wide on two ounce copper is about 0.5 milliohm. A connector pair is often 1 milliohm. A fuse is more. The switch becomes one term in a sum, and the sum is what decides the loss, which is why a part this low is chosen for a current path and not for a switching cell.

80 V covers a 48 V pack at the top of charge, a 60 V PoE rail, a 48 V telecom rectifier and a 48 V motor drive. The derating rule at 80 per cent gives 64 V continuous, which is the number to compare with the highest voltage the node will see in normal operation.

Key data for the VBGP1802

ConfigurationSingle N channel
PackageTO247, through hole
VDS80 V
VGSPlus or minus 20 V
Vth3.5 V typical
ID250 A, a die figure at a 25 C case
RDS(on) at 10 V2.1 milliohm
TechnologyShielded gate trench
Body diodeIntrinsic, cathode at the drain
Loss at 100 A21 W through the channel
Loss at 50 A5.25 W through the channel
Gate chargeNot printed, ask for the curve at 48 V drain

Where the 2.1 milliohm goes when the board is built

At 100 A the channel loses 21 W and the connection to it loses more than the calculation suggests. The TO247 source lead is roughly 0.15 milliohm, the solder joint under it a little less, and the copper that spreads from the lead into the plane can add half a milliohm if it is narrow. The result is that a part quoted at 2.1 milliohm measures closer to 3 milliohm across the terminals of a real board.

The measurement point matters for the same reason. A four wire measurement taken at the lead tips includes the lead, and a measurement taken across the die does not. When a candidate is compared against an original, both have to be measured the same way, or a 0.5 milliohm difference that is really lead geometry will look like a die difference.

The current does not spread evenly either. In a TO247 the source lead is on one side of the die, so the current crowds at that edge. At 250 A the crowding is what sets the local temperature, and the datasheet thermal resistance is an average over the die, not the hottest point.

Switching a very large die

A 2.1 milliohm die is physically large, and a large die has a large gate charge and a large output capacitance. That is the trade at the heart of this part: the conduction loss is tiny and the switching loss is not. At 100 kHz with a 48 V bus the crossover loss can be 15 to 25 W, which is more than the conduction loss at 50 A.

For that reason this part suits a low frequency path, an ORing switch, a battery disconnect, a load switch and a motor drive at 20 to 50 kHz. It does not suit a 300 kHz synchronous buck, where a smaller die with a third of the gate charge will win despite a higher resistance.

Driving a large gate also takes current. The peak gate current from a driver rated at 2 A gives a turn on in about 50 ns, which at 48 V and 100 A is a di/dt of 2 A per nanosecond and needs a tight loop. A weak driver leaves the die in the linear region for longer and the loss lands on the die instead of the heatsink.

Where the part fits and where it does not

It fits an ORing switch on a 48 V bus, a battery disconnect on a 48 V pack, a load switch on a 24 V or 36 V rail, a motor drive at 20 to 50 kHz, and a synchronous rectifier on a low voltage high current output. It does not fit a 96 V pack, a converter that runs above 150 kHz, or a board where the gate driver cannot deliver an amp of peak current. In practice this part is run at 40 to 80 A continuous with a proper bus and a real heatsink, and the current column is headroom for pulses.

For a 2.1 milliohm switch on a current path, the parameters that decide behaviour are the threshold, the resistance at the gate voltage in use and the way the current enters the die. Our how to reduce component cost page covers where a lower cost equivalent can be used and where the loss it adds outweighs the price difference.

The sourcing side of this part is covered on the safety stock planning. For a very low resistance part used on one rail, that page covers how a buffer is sized against the build plan.

Questions we get on this code

Can it carry 250 A? The die can at a 25 C case, the leads and the joint cannot for long. A screw terminal and a thick copper bus are needed before the current column means anything.

Does it need a gate resistor? Yes. A die this size rings on the gate and on the drain, and a 2 to 5 ohm resistor plus a short return is the minimum.

How does it compare with two 4 milliohm parts in parallel? Two parts give 2 milliohm with two gate drives and a sharing problem. One part gives 2.1 milliohm with one drive and no sharing, which is usually the better trade below 100 A.

What should a purchase order carry? Part number, TO247, and the packing form. We confirm tube or taped quantity on the offer.