Contact Us

VBA3860

Brand: VBsemi
VBsemi VBA3860 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA3860 — Discrete & Power Semiconductors | Superb Automation

VBA3860

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA3860 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA3860: an 80 V dual N channel at 3.5 A in SOP8

The VBA3860 is a dual N channel MOSFET in an SOP8 body with 80 V per device, a plus or minus 20 V gate window, a 1.7 V threshold, a 3.5 A current figure and a single resistance column, 62 milliohm at a 10 V gate, on trench silicon.

Eighty volts is a different world from 30 V. It is the class that a 48 V telecom rail, a 36 V battery pack and a 60 V solar input all need once the transients are counted, and it is the class where the resistance per unit area starts to hurt. A 62 milliohm die at 80 V is a reasonable device; the same resistance at 30 V would be a poor one.

The single resistance column at 10 V is a statement in itself. The part is specified with a 10 V gate, which means the catalogue expects a gate drive above 4.5 V, and no 4.5 V figure is published because the die at that drive is not a number the vendor wants to stand behind. A board that can only offer 5 V should not assume the 62 milliohm applies.

Key data for the VBA3860

ConfigurationDual N channel, two independent devices
PackageSOP8, surface mount, 1.27 mm pitch
VDS80 V per device
VGSPlus or minus 20 V
Vth1.7 V
ID3.5 A
RDS(on) at 10 V62 milliohm
RDS(on) at 4.5 VNot published on the catalogue page
TechnologyTrench
Gate chargeNot published on the catalogue page
Body diodeOne per channel, reverse recovery matters at 80 V
Thermal pathEight leads, shared frame
Avalanche ratingNot published on the catalogue page

Why an 80 V part is specified at 10 V and not at 4.5 V

A 1.7 V threshold with a 4.5 V gate leaves 2.8 V of overdrive, which is enough for a 30 V die and marginal for an 80 V die. The reason is the drift region: an 80 V trench device has a lightly doped layer between the channel and the drain, and that layer adds a resistance that does not respond to gate voltage. At low gate drive the channel resistance is a larger share of a larger total, and the resulting number is both higher and more variable than at 10 V.

So the vendor publishes what is stable. That is honest, and it puts the burden on the board: a gate drive of 10 V has to be available, either from a 12 V rail through a resistor with a clamp or from a small charge pump. A microcontroller pin driving this part directly will produce a switch that works on the bench and gets hot in the field.

The 1.7 V threshold is still useful, because it sets the point at which the part starts to conduct and therefore the point at which leakage becomes measurable. For an 80 V part the leakage at high temperature is the number to check in the data sheet, since a die with 62 milliohm in the on state can still leak microamps at 125 C and 80 V.

3.5 A, 62 milliohm and the frame

At 62 milliohm and 3.5 A the loss in one die is 760 mW, and two channels at that current give 1.52 W in a package with eight leads and no exposed pad. That is beyond what still air can pass, so the 3.5 A figure applies to a single channel on a board with a decent copper landing, or to two channels at about 2 A each.

The 80 V rating matters in exactly the applications where the current is small: a bleed resistor path, a precharge switch, a relay coil driver on a 48 V rail, a string of LEDs at 200 mA. In all of those the die is far from its thermal limit and the voltage rating is the whole point.

Where the part does not fit is a 48 V hot swap at 10 A. The resistance is too high for the loss and the SOP8 cannot pass the heat. That application needs a larger body with a tab, and the choice is a package question before it is a die question.

At 80 V the gate drive deserves as much attention as the die. A high side switch on a 48 V rail needs a gate 10 V above the source, which is 58 V, and no logic pin can supply that. A bootstrap capacitor and diode from a 12 V rail is the usual arrangement, and the capacitor has to hold its charge across the whole on time, which for a static load switch means it does not work at all. A static high side switch at 48 V therefore needs either a small charge pump or a P channel, and the dual N part here belongs on the low side or behind a floating driver.

Where it fits

It fits a 48 V precharge or bleed path, a relay coil driver, a 60 V solar input disconnect at low current, an LED string switch, and any 48 V signal level switching where a 30 V part would be marginal. It does not fit a 10 A hot swap, and it does not fit a board with only a 5 V gate rail unless the data sheet confirms a 4.5 V column.

Our safety stock planning page covers how a buffer is sized for a part that has few alternatives, which an 80 V dual in an SOP8 body usually is.

The sourcing side of this part is covered on the component shortage forecast. For an 80 V part with a narrow second source list, that page covers how a shortage is seen before it stops a line.

Questions we get on this code

Can it be driven from 5 V? Not to the published 62 milliohm. The 4.5 V column is not published, so the resistance at 5 V has to come from the data sheet curve.

Is 80 V enough for a 48 V rail? Yes, with 32 V of margin, which covers a clamped load dump and the switch node ring. An unclamped inductive event still needs a suppressor.

Can both channels carry 3.5 A at once? Not in an SOP8 at ordinary ambient. Use 2 A each, or one channel at 3.5 A with the other idle.

Do you have a 4.5 V specified alternative? We can look for one, and the trade is usually a lower voltage rating or a larger body.