VB4610N
Product Specifications
VB4610N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB4610N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB4610N: two 60 V P channels in a six lead SOT23
The VB4610N is a dual P channel MOSFET in a SOT23 six lead body, with a minus 60 V drain to source rating, a plus or minus 20 V gate window, a threshold of minus 1.7 V, a drain current of minus 4.5 A, and an on resistance of 85 milliohm at a 4.5 V gate and 70 milliohm at 10 V.
Two P channels in one body is a narrow but useful product. It is the high side of a bridge with no bootstrap, a pair of redundant supply switches, a bidirectional battery disconnect, or two independent loads on the same 48 V rail that have to be switched from the positive side.
The resistance tells the story of P channel silicon at 60 V. The N channel part in the same body carries 4.2 A at 48 milliohm, and this one carries 4.5 A at 70 milliohm, so the P channel needs a die about 45 per cent larger for a slightly worse result.
Key data for the VB4610N
| Configuration | Dual P channel, independent |
| Package | SOT23, six leads, surface mount |
| VDS | Minus 60 V |
| VGS | Plus or minus 20 V |
| Vth | Minus 1.7 V |
| ID | Minus 4.5 A |
| RDS(on) at 4.5 V | 85 milliohm |
| RDS(on) at 10 V | 70 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page, expect more than the N channel counterpart at the same resistance |
| Thermal limit | About 400 to 500 milliwatt in total for the body |
| Body diode | Intrinsic, conducts from drain to source when the drain is above the source |
Driving two P channels from one signal
The gate of a P channel has to be pulled below its source to turn on, and both sources sit on the rail in the usual high side arrangement. That means the gate network is referenced to a node that moves, and the drive has to survive the full rail voltage between gate and source when the part is off.
With a 20 V window and a 48 V rail the gate cannot simply be left floating: a resistor from gate to source holds it off, and a small N channel or a transistor to ground pulls it on. The resistor value trades off leakage against turn off speed, and at 48 V a 10 k resistor wastes 4.8 milliwatt per channel, which for two channels in a standby product is 9.6 milliwatt that the specification may not allow.
A 100 k resistor wastes under a milliwatt and turns off more slowly, and at 85 milliohm and a few amps the slow turn off is a real loss mechanism. The usual compromise is 22 to 47 k with a small capacitor to set the edge, and the numbers should be checked against the gate charge, which this page does not publish.
Eighty five milliohm at 4.5 V against seventy at 10 V
A 17 per cent improvement between the two gate columns is a modest ratio, and it means the die is not strongly optimised for low voltage drive. At a 4.5 V gate the part is usable but not at its best; at 10 V it is at the published figure. For a 48 V system with a 12 V housekeeping rail, driving the gate 10 V below the source is straightforward and gives the 70 milliohm column.
At 3.3 V of drive the overdrive over a minus 1.7 V threshold is 1.6 V, and the resistance can be expected to rise by half again. That puts a 2 A channel at 250 milliwatt instead of 170, which a small body can still pass but only on a good pad.
The gate window of 20 V is what matters at 48 V. A P channel whose source sits at 48 V and whose gate is pulled to 38 V has 10 V across the oxide, which is half the rating. A transient that pulls the gate to ground gives 48 V across gate and source, which destroys the part. The series resistor and the clamp are therefore not optional in a 48 V system, they are the circuit.
Two channels on one rail and the leakage question
In a product that has to hold a load off while the rest of the board sleeps, the leakage of the switch matters as much as its resistance. A 60 V P channel with two 100 k gate resistors draws a few microamps from the rail, and the off state leakage of the die adds to it. For a battery product that is the number that decides whether the standby specification is met.
The catalogue page does not publish off state leakage. Ask for it before committing a battery powered product, because a part that leaks 10 microamps per channel is 20 microamps for the pair and a meaningful share of a 100 microamp standby budget.
Our excess inventory management page covers how excess is identified and how age is handled, which matters for a 60 V P channel bought in programme quantities, because the die is large and the reels are expensive.
The sourcing side of this part is covered on the how to reduce component cost. For a dual P channel that only a few sources build, that page covers where a lower cost equivalent can be used without changing behaviour.
Questions we get on this code
Can the two channels be used as a bidirectional switch? Yes, wired source to source or drain to drain, which puts the two body diodes in opposition and blocks in both directions when both gates are off.
Is 4.5 A per channel with both on? No. One figure for the body, so plan on 1.5 to 2 A per channel when both conduct.
Does it need a gate clamp at 24 V? A 24 V rail with the gate at ground gives 24 V across gate and source, which exceeds the 20 V window. A divider or a zener is needed.
What is the second source position? Dual P channels at 60 V in a small body have few sources. Send the original number and we check the pin map and the gate window before offering an alternative.