VB3658
Product Specifications
VB3658
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB3658 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB3658: two 60 V N channels in a six lead SOT23
The VB3658 is a dual N channel MOSFET in a SOT23 six lead body, with a 60 V drain to source rating, a plus or minus 20 V gate window, a threshold of 1.7 V, a drain current of 4.2 A, and an on resistance of 60 milliohm at a 4.5 V gate and 48 milliohm at 10 V.
Sixty volts is the class that covers a 48 V telecom rail, a 36 V battery string and the primary side of an isolated converter below 100 W. In a six lead plastic body the current is small, which suits the control and housekeeping side of those supplies rather than the power path.
Two channels in one body suit a push pull gate drive, a pair of relays, a bidirectional block on a 48 V signal, or the two switches of a small active clamp.
Key data for the VB3658
| Configuration | Dual N channel, independent |
| Package | SOT23, six leads, surface mount |
| VDS | 60 V |
| VGS | Plus or minus 20 V |
| Vth | 1.7 V |
| ID | 4.2 A |
| RDS(on) at 4.5 V | 60 milliohm |
| RDS(on) at 10 V | 48 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Thermal limit | About 400 to 500 milliwatt in total for the body |
| Body diode | Intrinsic, anode at source, recovery not published |
Sixty volts on a 48 V rail in a small body
A 48 V rail with a 10 per cent tolerance reaches 52.8 V and a switching node on top of that can ring past the rating. In a small plastic body the snubber has to absorb the difference, because there is no room for a large die and no avalanche rating published.
Sixty volts is the safe choice for a 48 V rail only when the circuit keeps the loop small and the switch node damped. A converter that puts the input capacitor 20 millimetres from the switch sees a ring of 15 V on a 2 A edge, which is 68 V at the peak and outside the rating. The fix is a capacitor within 5 millimetres and a resistor capacitor snubber across the low side switch.
For a 36 V battery string sixty volts is comfortable, because the peak with charging and ringing lands near 45 V. That is where a part like this belongs in a battery tool or a light electric vehicle auxiliary supply.
Four and a half volts against ten, and the drive question
The resistance falls from 60 to 48 milliohm between a 4.5 V and a 10 V gate, a fifth of the value, which is a normal ratio for a 60 V logic level die. A 1.7 V threshold means the part is usable at 4.5 V and good at 10 V, and a 5 V gate drive is the sensible default.
At 3.3 V the overdrive is 1.6 V, which is at the bottom of the useful range for a 60 V die. The resistance is not published there and should be assumed 30 to 50 per cent above the 4.5 V column, which at 2 A turns 240 milliwatt into 320 and changes the thermal sum on a small body.
The 20 V gate window is generous and it is what lets the part be driven from a 12 V rail through a resistor, which is a common arrangement in a 48 V system where a 12 V housekeeping rail is available.
Two channels in one body on a 48 V board
The main advantage is that the pair switches a push pull or a half bridge with a short loop between them, which at 48 V is worth more than on a low voltage board, because the loop inductance produces a larger voltage excursion for the same current slope.
The main disadvantage is the same as everywhere in this family: the two dice share a lead frame, so the loss of both arrives at one place. At 1.5 A per channel and 48 milliohm the pair dissipates 216 milliwatt, which is fine. At 3 A each it is 864 milliwatt and the body is past its limit.
Isolation between the channels is a package question. A high side channel that sits on a 48 V node next to a channel on ground puts 48 V across the package, and the pin spacing of a six lead SOT23 is a few tenths of a millimetre. The data sheet creepage figure is the number to check, and for a 48 V difference in a polluted environment a larger body is the right answer.
Our component lead time solutions page covers how a date is quoted and what is confirmed before it is promised, which for a 60 V dual in a small body is worth knowing early, because the family has few sources.
The sourcing side of this part is covered on the supplier onboarding checklist. For a 60 V dual in a small body, that page covers what a new source has to document before the first order.
Questions we get on this code
Can it switch a 48 V relay? Yes, with a flyback diode and a gate drive of 10 V. The coil current is under an amp and the diode clamps the inductive spike.
Is the 4.2 A rating for both channels? One figure for the body. Use 1.5 to 2 A per channel with both conducting.
What about avalanche? No avalanche rating is published on the catalogue page, so a circuit that can put energy into the drain at turn off has to clamp externally rather than rely on the die.
Is there a P channel counterpart for a complementary stage? Yes, the same family carries a 60 V P channel in this body. Ask for the code and we quote the pair together.