Contact Us

VB1240

Brand: VBsemi
VBsemi VB1240 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VB1240 — Discrete & Power Semiconductors | Superb Automation

VB1240

VBsemi — Discrete & Power Semiconductors

Product Overview

The VB1240 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VB1240: a 20 V N channel with a 12 V gate window

The VB1240 is a single N channel MOSFET in a SOT23 three lead body, with a 20 V drain to source rating, a plus or minus 12 V gate window, a threshold between 0.5 and 1.5 V, a drain current of 6 A, and an on resistance of 42 milliohm at a 2.5 V gate and 28 milliohm at 4.5 V.

The number that deserves attention is not the 6 A. It is the 12 V gate window, which is the tightest of any part in this catalogue band and half of what a SOT23 device usually allows. A 12 V window means the gate cannot be tied to a 12 V rail directly, and a supply transient above 14 V reaches the gate oxide through whatever drives it.

Everything else about the part is ordinary for the body: a logic level die, a 20 V rating that suits a 5 V or 12 V rail with a clamp, and a resistance that is competitive for a SOT23 at 28 milliohm.

Key data for the VB1240

ConfigurationSingle N channel
PackageSOT23, three leads, surface mount
VDS20 V
VGSPlus or minus 12 V
Vth0.5 to 1.5 V
ID6 A
RDS(on) at 2.5 V42 milliohm
RDS(on) at 4.5 V28 milliohm
TechnologyTrench
Gate chargeNot published on the catalogue page
Thermal limitAbout 350 to 400 milliwatt in still air on a normal pad
Body diodeIntrinsic, anode at source

The 6 A claim against a SOT23 pad

Six amps through 28 milliohm is 1.0 W. A SOT23 with three leads passes about 350 to 400 milliwatt to still air on a typical pad, and about 600 milliwatt on a generous one. The 6 A figure is therefore a die and bond wire limit, and the working current is between 2 and 3 A.

Run the arithmetic properly. At 2 A the loss is 112 milliwatt and the junction rise is under 50 C on a normal pad, which is comfortable. At 3 A it is 252 milliwatt and about 100 C of rise, which is at the edge in a 60 C ambient. At 4 A it is 448 milliwatt and the junction is above 180 C in a warm box, which is not a product, it is a test.

The three lead body also sets the current through the leads, not only through the die. A SOT23 lead is a thin strip of copper alloy and its resistance is a real part of the total; the resistance figure on the catalogue page is die plus package at the specified current, so a board that runs at ten times the measurement current sees more than the table.

The 12 V gate window is the parameter that shapes the circuit

A 12 V window rules out the simplest high side arrangement, where the gate is pulled to a rail that can reach 12 V, because the gate to source voltage would sit exactly at the limit with no margin for the supply tolerance. It also rules out a 12 V gate drive in a circuit where the source is not at ground, because the gate to source voltage then depends on the source potential.

In practice a 12 V window is fine for two arrangements: a low side switch driven from 4.5 or 5 V logic, and a high side switch driven through a resistor from a 10 V rail with a clamp. Anything else needs a gate clamp, which is one zener and one resistor and turns a two part circuit into a four part one.

The window also has a transient meaning. A gate oxide that is rated at 12 V survives a spike of 15 V for a short time, but a repetitive spike at every switching edge is a wear mechanism. A resistor at the gate and a short return path are the mitigation, and the resistor is also what damps the resonance between the gate capacitance and the trace.

A logic level die at the bottom of its range

The resistance moves from 42 to 28 milliohm between a 2.5 V and a 4.5 V gate, a third of the value, which is a healthy sign: the die is well enhanced at 4.5 V and usable but not optimal at 2.5 V. A 3.3 V microcontroller pin sits between the two columns and should be treated as somewhere around 33 to 35 milliohm, since the resistance falls roughly with the square of the overdrive above threshold.

That estimate is a reason to ask for the output characteristic rather than a number to put in a thermal calculation. The catalogue publishes two points; the curve between them is what a circuit at 3.3 V actually needs.

Our how to reduce component cost page covers where a lower cost equivalent can be used without changing behaviour, and a 20 V single N channel in SOT23 is one of the most substitutable lines on a bill of material, which is both an opportunity and a risk if the substitution is made on resistance alone.

The sourcing side of this part is covered on the one stop BOM sourcing. For a switch that ships beside its controller and passives, that page covers how the group is bought together.

Questions we get on this code

Can it replace a part with a 20 V gate window? Only if the circuit never applies more than 12 V gate to source. A wider window part is compatible with a narrower one, not the other way round.

Is 6 A real for a load switch? No. Use 2 to 3 A continuous and check the pulse rating if the load has inrush.

What is the difference from the VB1240B? The B variant has a wider gate window and a lower resistance in the same body. If the board can accept a 20 V window, the B is the better part.

How is it supplied? SOT23 parts normally ship on 3000 piece reels. The reel size is confirmed on the quotation, and a smaller quantity comes from a broken reel.