Contact Us

Solder Paste Storage and Thaw Control

Solder Paste Storage and Thaw Control

Solder paste is the cheapest material on the line and the one that decides most of the morning. A jar taken out of the fridge at half past seven, opened at eight and printed at half past eight does not behave like the same jar printed at eleven, and the difference never shows on the printer display. It shows in the SPI volume trend and, a few hours later, in the joints.

Storage and thaw control is a short procedure that is easy to skip when the line is busy. The cost of skipping it is not a defect that can be traced back to the paste, because by the time the joints are inspected the jar is gone.

What the label on the jar already says

Every jar arrives with a batch, a production date and a storage range, usually 2 to 10 degrees C. Unopened, the paste is good for the shelf life printed on it. Opened, the clock changes: the container is in contact with room air, the flux begins to take up moisture, and the number that matters is the time since it left the fridge rather than the date on the label.

The label is also the first record. If the batch cannot be read, the lot cannot be traced back to the print that used it.

Thaw is time, not heat

A 500 g jar takes two to four hours to reach room temperature in a sealed container. A syringe takes less. The jar stands upright, lid tight, in the paste area, and nobody helps it along.

Heating the jar is the one thing that reliably ruins paste. Warm water, an oven or a hot plate takes the flux above its working temperature before the powder is dispersed, the flux separates, and the paste prints with a skin that slumps differently from the batch beside it. That cannot be seen on the print. It appears as inconsistent deposit volume across a shift.

Condensation is the hidden problem

In a humid room a cold jar pulls water onto the lid and the shoulder as soon as it is opened. That water goes into the paste when the jar is stirred, and moisture in the flux is one of the causes of solder balls and spatter that later get blamed on the profile. Wiping the outside of the container before opening is a two second habit that removes most of it.

The print area runs at 22 plus or minus 3 degrees C and 45 to 65 per cent relative humidity, which is the range the paste was formulated for.

Mixing and press-out

After thaw the paste is stirred gently for about a minute, by hand or on a slow roller, to bring the powder back into suspension. High shear mixing whips air in, and air in the paste prints as voids and slumps as soon as the stencil lifts. The first press-out from a new jar goes on a test print, not on product.

Open time against stencil life

Two numbers get confused. Open time is how long the paste can sit in an open jar. Stencil life is how long a roll can stay on the printer and still release cleanly, and it is the shorter of the two. The practical test is not the clock but the print: if the roll stops releasing cleanly, skips apertures or leaves a ragged edge, the paste is finished for that run whether it has been two hours or six. Measuring deposit volume with the SPI shows which of the two numbers is being reached.

The record that survives an audit

A temperature log is worth more than a policy. The fridge runs at 2 to 10 degrees C and is checked at the start of each shift, the jar is signed out and back in, and the oldest batch is used first. When a customer asks which lot went into a serial number, the answer comes from that log rather than from memory.

What goes wrong

What the line reportsWhere it comes fromWhat to change
Deposit volume falls through the shiftPaste drying on the roll, past its stencil lifeAdd fresh paste in small amounts and re-measure the deposit
Solder balls and spatter on fine pitch partsMoisture in the flux from a jar opened too coldFull thaw before opening, wipe the lid and shoulder first
Paste will not release from small aperturesJar not fully thawed, viscosity still highTwo to four hours thaw and a check on the jar temperature
Skips appear on one printer onlyDried paste left in the aperturesUnder wipe between prints, aperture check at each break
Voids under a QFN thermal padAir whipped into the paste during mixingGentle stirring by hand or a slow roller
The batch cannot be traced after the factLabel unreadable, no log keptRecord the batch at press-out against the work order

How SUPERB PCBA controls it

Paste is stored at 2 to 10 degrees C, logged in and out, and thawed sealed for the time the pack size needs before it goes near a printer. Every run is measured: the 3D SPI on the line reports deposit volume per pad, so a lot that starts to fall off is visible before AOI finds a joint. The measurement side, deposit volume and print definition, is set out under solder paste inspection.

The same discipline applies to the parts around the paste. Moisture sensitive components are baked at 125 degrees C per J-STD-033 when floor life is exceeded, covered under MSL and bake control, and stencil condition and aperture cleaning under tooling and stencil control.

Questions buyers ask

Can paste be used straight from the fridge on a cold morning?

No. A cold jar prints at higher viscosity, releases poorly from small apertures, and pulls water onto the surface once opened.

Does paste expire while it sits in the fridge?

The unopened shelf life applies inside the storage range. A jar left out overnight and put back is not the same jar.

Is lead free paste more sensitive?

SAC305 needs a higher peak and its flux is used up sooner, so the same storage discipline matters more rather than less.

Next step

Send the BOM and the assembly package for the build, with the paste brand or alloy if your process specifies one. The process data that comes back covers the paste, the stencil, the profile and the SPI limits used on the lot, and any deviation is raised before the run rather than after it.