Contact Us

PCB Panelization for Assembly

PCB Panelization for Assembly

A panel that suits the board supplier and not the line is easy to recognise. The first build runs, the placement is fine, and then the rework starts: cracked 0402s next to the tabs, a corner that will not sit flat on the printer, a rail too narrow for the clamps. Nothing is defective on paper.

Panelization for assembly is a set of constraints that come from the machines rather than the board: printer frame, conveyor, the field the cameras have to see, and the way the panel is separated. Each is cheap at the panel stage and expensive once the order is released.

What the line constrains before anything else

The print area is the first limit. The automatic printer on our lines takes a 400 x 340 mm panel, and the panel plus its clamping margin has to sit inside that. A panel that is 10 mm too wide is not a small problem, it means a different printer or a smaller array.

Then the field of view. SPI, AOI and X-ray have to reach the array without fouling the rails, and conveyor width and warpage come from the panel.

The two numbers that decide the array

Cost per board and handling cost pull in opposite directions. A large array uses the panel better and lowers the cost per board, and it also concentrates the risk: one warped panel, one misprint or one placement error affects every board on it. Small arrays handle better and cost more per board. The arithmetic is worked through on this panel cost comparison.

Filling a 622 x 1092 mm panel with forty small boards is the cheapest way to build them and the worst way to handle them when the boards are 0.8 mm thick. The answer is usually an array that fits the printer, keeps a rail on all four sides, and stays inside the warpage limit rather than the utilisation maximum.

Rails, tooling holes and clamping

A rail of 3 mm is the minimum the line can grip. Below that the clamps have nothing to hold and the panel shifts during printing. Rails also have to be free of components, and free of copper that can short against the clamps.

Tooling holes go at the panel corners where the fixture needs them, clear of the marks and the conveyor. Holes that do not match the fixture mean the panel is built on a pallet, which adds handling to every board.

Fiducials belong on the panel that survives

The most common panel error we see is a good set of marks placed on a rail that is cut away. The marks work on the first build, because they are still there, and the second build starts without them. Marks belong on the panel body or on a rail that is retained: three of them, non collinear, on the finish that ships.

Sizes, clearances and the contrast problem are set out on the fiducial mark requirements page. What matters at the panel stage is position relative to the separation method.

The separation method decides the rework rate

V-cut is fast, leaves a straight edge, and puts bending stress along the whole cut line. Tab routing with mouse bites is slower and concentrates the stress in a few places. On a board with chip capacitors near the edge, or a BGA within a few millimetres of the cut, the second is usually the safer choice.

The V-cut side of the line handles boards 60 to 480 mm wide, up to 30 cuts in a panel, with a residual web of 0.25 to 0.50 mm. Those are not targets but the range in which the cut works. A thicker web will not close, a thinner one breaks in the machine instead of in the operator's hands.

Warpage and thickness

Warpage is measured after reflow, and it decides whether a panel can go through the line again. We work to 0.75 per cent on SMT panels and 0.5 per cent on HDI and rigid flex. A large array of thin boards, or a panel with heavy copper on one side only, warps more than the same boards built singly.

Boards from 0.6 to 3.2 mm run on the standard line. A 0.6 mm board in a large array needs support pins under the middle, or the panel sags and the inner boards see a different curve from the ones on the rail.

What shows up on the line

What the line reportsWhere it comes fromWhat to change
Panel shifts during printing, the print smears at one edgeRail under 3 mm, or clamps pressing on copperWiden the rail to 3 mm and clear copper under the clamps
Cracks in 0402 parts next to the breakawayV-cut stress with parts close to the cut lineMove the parts back, or switch to tab routing with mouse bites
SPI reads the array at an anglePanel outline not straight, or marks on a railPut the marks on the body and keep the outline clean
The middle of the panel reflows colder than the edgesLarge array, thin board, nothing under the middleSupport pins under the array, or split it into two panels
The second lot starts with no alignment at allMarks were on rails that were removed after the first lotRetain a rail, or move the marks onto the body

How SUPERB PCBA handles a panel

Panels are reviewed before release against the printer, the camera fields and the separation method, not only against utilisation. The review happens before the first panel is built, on the same machines that will run the order, and it covers rails and tooling holes as well as the array. The stencil and fixture side of that check sits under tooling and stencil control.

Where a panel carries both reflow and through hole parts, the separation and the clamping have to work for a second pass as well, which is covered under mixed technology assembly.

Questions buyers ask

Can a panel run without rails?

On some lines yes, if the machine clamps the board edge directly and the board is thick enough. On a thin board with fine pitch parts the rail is what keeps the panel flat, and the saving is not worth the placement error.

Does a bigger panel always cost less per board?

Up to the point where handling, warpage or a single misprint writes off forty boards at once. The cheapest array is usually the largest one that still meets the printer, the warpage limit and the separation method.

Should the tabs be on the long or the short edge?

Wherever the separation force ends up parallel to the weakest part of the board. That is a decision per board, made with the part positions in hand rather than from a rule.

Next step

Send the Gerber set, the BOM and the panel drawing if one exists. The panel is checked against the printer, the cameras, the warpage limit and the separation method before the order is released, and the answer comes back with an array that fits, or with the specific reason the current one does not.