Most checks on a new board happen in the middle. Stack-up, impedance, the fine pitch part under the camera. The edge is where a board that passed every electrical rule still stops, because the conveyor, the nozzle and the router all work in the last few millimetres and none of them negotiates.
PCB edge clearance for assembly is the set of distances a board keeps from its own outline so it can be built, tested and separated without a special process. Handled correctly, nobody mentions it. Missed, it shows up late: parts knocked off at the rail, mask chipped along the route, a corner that will not seat in the fixture.
Three edges on the same board
Three edges sit within a few millimetres of each other and each has its own keepout: the routed edge of the finished board, the V-score line where two boards meet, and the panel edge where the rail is gripped. A part clear of the finished outline can still sit on a rail that gets routed away, or inside the stress band of a score line.
The conveyor sets the first number
Every SMT line grips the panel on two parallel edges and pulls it through. Anything standing in the grip zone is crushed by the rail or pushes the panel out of level, and a panel that is not level prints uneven paste at that end. The printers we run give a 400 x 340 mm print area, so the rail position moves with panel size and the keepout moves with it.
Component bodies at the routed edge
A part placed close to a routed edge is not a problem while it is being placed, but the body overhangs the support, and during reflow the overhanging end heats differently from the supported end. Tall parts lean, and small chip parts next to the route are the ones that tombstone or shift.
Connectors may overhang, so one rule does not cover the whole edge. An overhanging body needs the route clear of its pins and latch, and the rail back far enough that the body never touches the conveyor.
Copper, mask and the 0.20 mm floor
Copper closer to the routed edge than 0.20 mm is exposed when the router bit tears the laminate, and a mask sliver that thin lifts during handling. We hold 0.20 mm as the floor from copper to board edge. A plane poured to the outline is the usual way the number is broken, because the pour follows the border and the border is where the router runs.
Mask has a second problem at the edge. A mask band narrower than the route tolerance disappears entirely on one board and stays on the next, so one part number ships with two appearances.
V-score lines are a stress band, not a line
A V-score cuts a groove on both faces and leaves a web that is broken later. We work to a residual of 0.25 to 0.50 mm with 0.10 mm tolerance, up to 30 cuts per panel and board width from 60 to 480 mm. The score is a controlled weak point, and the board beside it bends when it is broken.
Parts placed hard against a score line take that bend. The safe zone is wider than the groove: the groove plus the material that flexes when panels are separated. A part 0.3 mm from the score looks fine on the drawing and is the first to crack.
Where edge clearance goes wrong
| What the line shows | What caused it | What to change |
|---|---|---|
| Parts shift at one end of the panel only | Grip edge carries parts, so the panel is not held flat | Move the grip to a rail with no parts, or widen the rail |
| Mask chips along the route after depanelling | Copper or mask closer to the outline than 0.20 mm | Pull the pour back and keep a mask band wider than the route tolerance |
| A chip part cracks beside a score line | Part inside the band that flexes when panels are broken | Move the part away from the score, or separate by routing |
| Overhanging connector lifts at reflow | No support under the body, no clearance for the latch | Keep the route clear of pins and latch, support the body during print |
| Board does not seat in the test fixture | Test point or tall part inside the clamp zone | Move the point inboard, or open the fixture at that position |
Test points, shields and can frames
A test point near the edge is the quiet failure. The probe needs a clear approach and the fixture clamp needs somewhere to land that is not a pad. A point 1 mm from the outline can be placed and still unreachable at test, which is found after the first panel. Shield frames behave the same way: the ring has to be continuous, so a frame that runs to the edge loses part of it to the route.
Rails, tooling holes and the 3 mm rule
We work to a process rail of at least 3 mm on the gripped edges, with tooling holes clear of the part field. Panel size runs to 622 x 1092 mm, so the rail is cheap in material and expensive to add after the array is agreed. The rail is also where the fiducials live: a mark on a rail that survives is still there on the second build.
How SUPERB PCBA checks the edge
The edge is reviewed with the panel, before release: grip edges, rail width, score positions, copper to outline, mask band, overhanging connectors and test point access, all read against the same drawing. Where a board arrives with parts inside a keepout, the conflict is raised with the customer and settled before a panel is cut, because moving a part after tooling is the expensive version.
The copper side of the same edge is covered in trace to board edge distance, the array itself in PCB panelization for assembly, and the separation step in V-score and tab routing. Seven SMT lines run the first article on the machine that will build the order, so an edge problem shows up on one panel rather than one thousand.
Questions buyers ask
Is there one clearance number for the whole edge?
No. Copper, mask, part body, connector overhang and test access have different limits, and the grip edge is stricter than the two free edges.
Can a part sit on a rail that is routed off?
Only if the rail is retained until after reflow and the part is not in the route path. Most often it is cheaper to move the part inboard.
Does a V-score panel need more clearance than a routed one?
Yes, along the score. Routing leaves a clean edge with no web to break, so the stress band beside a score is the one to keep clear.
Next step
Send the Gerber set, the panel drawing and the BOM. The edge review comes back with the specific conflict and the smallest change that clears it, before tooling is made. If the order is already running, the first article record shows what the line actually held.