Contact Us

PCB Edge Plating

PCB Edge Plating

The board slides into a card cage and the contact fingers along the edge do the electrical work. Behind the fingers there is a 1.6 mm wall of laminate that has to carry plating as well, because a finger that stops at the surface leaves the cut edge bare. That wall is where moisture enters, where solder wicks at assembly, and where a ground contact drifts after a few hundred insertions.

PCB edge plating is judged at that wall, not on the top surface. A board can look correct from above and still fail, because the plating wrapped half a millimetre onto the surface and then stopped short of the profile.

What edge plating actually covers

Three features get called edge plating, and they are bought for different reasons. Plating the vertical wall passivates the laminate and joins top copper to bottom. The wrap is the band folding over onto both surfaces, and its width decides whether a castellated joint has anything to wick into. The bevel guides the board into a connector, and it is the step that most often destroys the first two when it runs late.

Castellations are the fourth case: half holes opened into the edge after plating, where the barrel plating becomes the joint surface, detailed under castellated holes for module boards.

Which edges to plate, by application

ApplicationWhat the plating is doingWhat the drawing has to stateWhat fails when it is left open
Card edge connectorMating surface plus a plated wall behind the fingersWhich edge, finger length, hard gold thickness, bevel angle, wrap widthBare laminate behind the last finger; gold worn through at the bevel
Castellated moduleBarrel plating becomes the joint to the carrierHalf hole diameter, pitch, wall plating thickness, wrapHalf hole with a dry wall; module lifts on one side after reflow
Chassis ground contactLow resistance path from board ground to a case or gasketPlated area, finish, flatness at the contact band, no mask on the contactGround noise that moves when the screws are torqued
Shield can to board edgeSolderable land that runs along the profileWrap width, a finish that wets, keep out for the can wallSolder fillet that runs off the edge and balls on the fixture
Power board with thick copperCurrent carrying edge, sometimes a busbar landOuter copper weight, plating thickness, edge flatnessHot spot at the edge where plating is thinner than the foil

Name the edges by their position in the outline, not by the word edge. On a board with four edges and two of them plated, an instruction that says plate the edge is an instruction to guess.

Numbers that belong on the drawing

For a mating surface the choice is hard gold over nickel, with the gold thickness set by insertion count. The thickness that is actually bought is covered in hard gold thickness for edge connectors. For an edge that only needs sealing and grounding, ENIG at 100 to 200 micro inches of nickel and 2 to 3 micro inches of gold is the usual call.

The bevel is the number buyers forget. Angle and depth have to match the connector, and the bevel is cut after plating, which is where a good edge becomes a bare one. A bevel drawn without an angle comes back as whatever the routing program was set to that day.

The process order that keeps the wall plated

Edge plating is a sequence problem before it is a chemistry problem: the wall can only be plated if it exists when the panel enters the line, and it only stays plated if nothing cuts it afterwards.

  1. Inner layers, lamination, drilling, and pattern plating to the required copper weight.
  2. Profile routed to the final outline, so the wall is at its finished position.
  3. Edge plating on the panel line, with the wrap width set by the mask pullback.
  4. Fingers masked and hard gold plated, so the gold lands on the wrap and not on the laminate.
  5. Bevel cut, with the angle and depth from the drawing.
  6. Electrical test, final inspection, and a cross section on the first panel to measure the wall.

Move the route after the plating step and the wall is cut back to laminate, which is how an edge measures zero plating in a cross section while the surface band looks perfect. Move the bevel before plating and the bevel itself is plated, which sounds better and behaves worse, because the bridge there is thin and cracks at the first insertion.

Where a plated edge goes wrong

Uneven thickness at inside corners comes first. Current density rises where the profile turns, so a wall at 25 micrometres on a straight run can measure half of that in a corner, and on a ground contact that is a resistance difference nobody sees until an EMC test. Then the mask dam between two fingers: it retreats during development, the plating between the fingers is exposed, and the first reflow bridges two contacts that were never meant to touch. Third is burr direction, because a burr on a plated edge lifts the board in the connector and gives an intermittent contact.

How SUPERB PCBA handles an edge plated board

Boards are produced at the PCB end in Jiangsu and Zhuhai and assembled in Shenzhen and Jiangxi, so the edge specification travels with the panel instead of being re interpreted at assembly. The published PCB envelope covers 1 to 20 layers on the FR-4 line and up to 68 layers on the high layer line, trace to board edge of 0.20 mm or more, profile tolerance of plus or minus 0.15 mm, and finger bevel across a 0.8 to 2.0 mm board at 20, 30, 45 or 60 degrees with a 5 degree tolerance. Outer copper goes to 10 OZ, which is what a current carrying edge needs.

Assembly then works from the same outline: placement to 01005 on seven SMT lines, reflow on a twelve zone nitrogen oven at under 500 ppm oxygen, optical inspection after reflow and X-ray where a joint is hidden, released to IPC-A-610 Class 2 or Class 3 as the drawing states. RF boards keep the same edge work inside their stack constraints, covered under RF and microwave PCB capability.

Questions buyers ask

Is edge plating the same as a castellated edge?

No. Edge plating coats the wall of a routed profile. A castellation is a half hole opened into that wall, so the plating runs inside the barrel and becomes the joint surface.

Can the edge be plated after the solder mask?

Only if the mask is pulled back from the profile by the wrap width. In practice the order is fixed by the bevel: plating, then mask, then bevel, with the bevel kept out of the plated band.

Next step

Send the Gerber set with a drawing that marks the plated edges, the bevel angle, the finger finish and the wrap width. The reply comes back with the panel and bevel drawing for approval, the process order, and the cross section and test reports that ship with the lot.