A castellation is a plated through hole that gets cut in half, and the only thing that makes it reliable is the order of three steps: drill, plate, then route through the centre of the hole. Specify a 0.6 to 0.8 mm finished hole on a pitch of 0.9 mm or more, require 20 micrometres of copper in the barrel before the cut, and put the castellation table on the fabrication drawing instead of leaving a hole sitting on the outline. Everything else on a module edge follows from that sentence.
What the callout has to contain
Hole and pitch. 0.6 mm is the practical floor for a drill that has to survive being cut through its own axis, and 0.8 mm is comfortable on a 1.0 mm pitch. A 1.27 mm pitch is what most radio modules use, and it leaves room for a 0.6 mm paste aperture. Below 0.5 mm the web between holes is thin enough to crack while the panel is routed.
Plating before routing. The barrel is a curved copper wall, and its thickness at the cut edge is the whole electrical and mechanical joint. Ask for 20 to 25 micrometres of copper, the same figure as a normal plated through hole, and state that the thickness is measured on a coupon after the cut rather than before it.
Cut position. The router has to pass through the centre of the hole, not near it. Pass it 0.1 mm off and the remaining barrel is a crescent that is 60 percent of the circumference on one side and 40 on the other, and the thin side is where the fillet breaks. A cut tolerance of 0.1 mm is achievable and worth writing down.
Pad and mask. Copper on both faces, mask opening on both faces, and no mask dam across the castellation. A dam under 0.15 mm will not survive the cut, and a dam that survives holds soldbarrel. The land on the module should extend about 0.2 mm past the edge so the fillet has somewhere to form.
Finish. HASL plugs a 0.6 mm half hole, and the plug is not uniform along a row. ENIG at 100 to 200 microinches of nickel and 2 to 3 microinches of gold leaves the barrel open and keeps it solderable after storage. Immersion silver works on a module edge and tarnishes in a sulphur atmosphere, which matters after six months in a warehouse.
Why the cut edge is the weak point
The barrel is drilled and plated, then the router removes half of it. The vertical face left behind carries no mask and no finish across its full thickness, so copper is exposed from the moment it is cut. That is a solderability clock: stored copper builds an oxide and a tarnish layer that a no-clean flux will not remove, and the first build shows it as a non-wetting toe on the outer castellations of the row.
Routing also throws a burr. The bit turns at tens of thousands of revolutions per minute and pushes copper instead of shearing it cleanly. A burr of 0.05 to 0.1 mm on the underside of a module holds the module off its land by exactly that amount, so the joint forms at the barrel and never reaches the pad. On a 1.0 mm pitch the same burr bridges to the next castellation.
The joint is stiff by nature. A castellated module is soldered at every point of the row, so the corners carry most of the load when the host bends: a 1.6 mm host bent 0.5 mm over 100 mm puts the corner fillet in tension. That is why corners fail on a drop test while the middle of the row is perfect.
Where a castellated row fails first, in order
Burr and copper residue inside the barrel. Visible under a microscope, invisible to AOI, and it appears as a bridge or an open at first article.
Resin smear. The router drags epoxy across the copper at the cut. The joint wets the smear and not the copper, and it fails a thermal cycle later.
Paste volume on the host. The aperture is a rectangle that has to extend past the module edge, because the solder must climb the half barrel. Too little paste leaves the barrel dry, too much travels along the row and bridges at a 1.0 mm pitch.
Three mistakes that appear on the first panel
Putting the row on a V-score line to save routing cost. A V-score cuts a groove and then snaps the panel, and snapping through a plated barrel tears the copper into an open circuit that still passes a visual check. Castellations need a router cut and a tab, and the tab cannot sit on the row.
Shrinking the pitch below the process floor. A 0.5 mm pitch with a 0.3 mm hole looks like a way to gain 6 mm of module width. It also leaves a 0.2 mm web between holes, a 0.15 mm ring of copper on each side of the cut, and a paste aperture that releases inconsistently. SUPERB PCB works from a 0.50 mm half hole with 0.90 mm spacing.
Calling the castellation out only in the outline layer. The shop sees a drill hit on the board edge and has to guess whether it is a rout, a slot or a plated feature. Put the hole size, the pitch, the quantity per row, the plating thickness and the cut tolerance in a table, and add the one sentence that plating happens before routing.
What SUPERB PCB and SUPERB Assembly support
Half holes from 0.50 mm with 0.90 mm spacing, mechanical drilling from 0.15 to 6.35 mm, plating of 20 micrometres or more, outline tolerance of 0.15 mm, and ENIG at 100 to 200 microinches of nickel with 2 to 3 microinches of gold. The FR-4 line runs 1 to 20 layers, the high layer count line reaches 68 layers, and panels go up to 622 by 1092 mm with a 3 mm process edge, which a castellation row needs free of parts on both sides.
On the assembly side the module is placed on a host footprint with 3D SPI before reflow, 3D AOI after it, and X-ray or CT to IPC-7095 where the module has a thermal pad underneath. Reflow runs a 12 zone profile with nitrogen below 500 ppm on SAC305. Where the module is larger than 25 by 25 mm or the host is thin, the module is staked at the corners after cleaning, because a castellated row is an electrical joint and not a mechanical anchor. The bare board routes and their limits are on PCB capability, the fine pitch window on HDI fabrication, and the assembly flow on turnkey PCBA assembly.
What to send
Send the Gerber set with drill and outline layers, the castellation table with hole size, pitch and quantity per row, the module and host thickness, the host land pattern, the finish and the storage interval before assembly. That confirms the pitch, the cut tolerance and the paste aperture before a panel is released.