Contact Us

RF Connector Soldering

RF Connector Soldering

The connector is often blamed for a return loss that is actually the launch. An SMA flange bolted to the edge of a board has four ground legs and a centre pin, and each of those joints is part of the transmission path. A pin soldered into a barrel that is half filled, or a ground leg sitting on a pad that never wet, shifts the impedance at the launch and shows up as a reflection the connector datasheet never promised.

RF connector soldering is a mechanical joint with an electrical consequence, and the two are checked in different ways.

Three ways a connector reaches the board

Joint typeHow it is madeWhere it goes wrong
Through-hole centre pin, flange groundsPin soldered in a plated barrel, ground legs into plated holes or onto padsShort fill in the pin barrel, ground leg with a fillet on one side only
Surface mount tab, edge launchTab reflowed with the rest of the board, ground tabs on the same paste printTab lifted by warpage, paste volume too low under the ground tabs
Press fit, no solderPin pressed into an eye of plated barrel with a controlled holeHole tolerance and plating thickness, since the joint carries no solder

The third type is not a soldering question at all, and mixing it into a soldering discussion is where build notes go wrong. The first two are what the rest of this page covers.

The ground path is the joint that matters

A connector's ground legs are not mechanical anchors. They are the return path for the field between the centre pin and the shell, and the current in them is not small. Four legs with a full fillet give a low inductance path around the launch. Four legs with one dry joint give a path that behaves like a slot antenna at the frequency where the leg length is a quarter wave, and the symptom is a notch in the response that moves when the cable is touched.

The practical rule is that every ground leg gets the same treatment as the centre pin, on the same side, in the same pass. A leg that is skipped because it is under the body is the one that fails.

Heat, and what the laminate will take

An RF board is often the least heat-tolerant board in the building. PTFE laminates soften and cold flow, and the coefficient of expansion in the z axis is an order of magnitude above FR-4, which is why a barrel in PTFE is more sensitive to iron time than a barrel in FR-4. Thermoset materials such as RO4003C and RO4350B take more heat but still delaminate when a joint is held at temperature for too long.

Three settings carry the process: the preheat that brings the board to within 100 C of the solder, the contact time on the joint, and the alloy. A tin lead alloy at 183 C gives the widest window on a PTFE board and is still common on RF hardware that is exempt from lead-free rules. Where lead-free is required, SAC305 with a hotter iron and a shorter contact is the usual compromise, and the joint is checked by cross section before the build is released.

Preforms and paste for a connector body

A connector with a large flange is hard to solder with an iron because the heat spreads across the body. A solder preform cut to the flange outline, or a ring around the pin, puts a measured amount of alloy exactly where the joint is and lets the whole assembly come to temperature in one pass. That is how a heavy connector is joined without a soldering iron at all, and it is also how a connector on a thick ground plane gets a full fillet without a 20 second contact.

Paste works where the joint is on the same side as the print, and preforms work where the joint is not. Both need the same flux decision, and that decision belongs to the customer, because residue inside a connector body is not cleanable after assembly.

What the check covers

Optical inspection reads the fillet on the centre pin and on each ground leg, and it covers the launch side only. X-ray shows the pin barrel fill as a density column and shows a ground leg that is short in the hole. Neither shows a joint that is mechanically complete and electrically poor because of a gap under a flange.

VSWR and insertion loss are measured on the finished assembly by the customer's lab or by a partner RF laboratory, not on the line, and that is stated up front rather than after a sample is asked for. What the line provides is the joint record: fill percentages, fillet photographs per connector position, and the preheat and contact data for the build.

How SUPERB PCBA runs an RF build

Boards run on Rogers RO4003C, RO4350B and RO4835, Taconic RF-35, TLY-5 and CER-10, and PTFE with plasma treatment before plating, with 0.05 mm line and space and impedance held to plus or minus 5 percent, or plus or minus 2 percent where the drawing calls for it. Mixed stacks with FR-4 are built with the RF layer as the controlled one.

Assembly runs on seven SMT lines with placement to 01005 at up to 40,000 CPH, reflow in a twelve zone nitrogen oven under 500 ppm oxygen, and selective soldering where a connector cannot take the wave or a full board reflow. Hand soldering follows a per joint instruction with tip temperature and contact time set by connector type and laminate, and preforms are stocked to the flange outlines on the drawing so the joint does not depend on how much solder an operator adds.

Inspection is 3D AOI after reflow, X-ray in 2D or CT for the pin barrels, and electrical test on the assembly. The assembly side is on RF PCB assembly, the solder supply side on solder wire, paste and preforms, and the nozzle path for a heavy connector on selective soldering process.

Questions buyers ask

Can a connector be hand soldered on a PTFE board?

Yes, with a short contact and a preheated board. Long contact on PTFE is what causes the barrel to move and the pad to lift, not the iron temperature on its own.

Is a preform better than paste for a flange?

For a large flange, usually yes, because the volume is fixed and the whole outline comes to temperature together. Paste is fine where the flange is small and the print can reach every pad.

Who measures the RF performance?

The customer's lab or a partner RF laboratory. The line supplies the joint record and the board data, and does not issue a VSWR figure of its own.

Next step

Send the BOM, the Gerber set, the stack drawing and the connector drawings with flange outlines and pin lengths. The reply comes back with the joint method for each connector position, the preform sizes where they are needed, the preheat and contact window for the laminate, and the inspection record the build will carry.