A via is a hole in a board, and leaving it open is an invitation. Solder wicks down the barrel during reflow and starves the joint on the far side. Flux and cleaning fluid sit inside and come back out as a stain two weeks later. On a fine pitch board the open barrel also collects paste that was meant for a pad half a millimetre away.
Via tenting and plugging is the answer, but the two words are not the same job, and neither is the same as filling. Picking the cheap option on a via that needed the expensive one produces a board that passes inspection and fails a thermal cycle.
Three treatments, three different problems
Tenting is a solder mask film over the via land: the via is covered, not closed. Plugging pushes material into the barrel to stop solder and fluid passing through. Filling puts material into the barrel and planarises it flush with the pad, which is the only one of the three that carries a component over the via.
The protection types and what each one gives up
| Type | What is done to the via | Where it is the right answer | What it does not do |
|---|---|---|---|
| I, tented | Mask over the land on both sides | Non functional vias in a low stress area | Seals nothing if the mask dome cracks at reflow |
| II, tented and covered | Mask over the land and across the surface around it | Vias near a component body where a bare ring is a risk | Same crack risk, and the ring is no longer testable |
| III, plugged | Material into the barrel from one side | Vias that must not pass solder or fluid, not under a pad | Leaves a dimple; not a placement surface |
| IV, plugged and covered | Plug plus mask over the land | Vias between fine pitch pads | Still not planar, so not for a pad on top |
| V, filled | Barrel filled and cured, not necessarily flush | Vias that carry current and must not void | Not a placement surface unless planarised |
| VI, filled and covered | Fill plus mask over the land | Filled vias that must stay out of contact with solder | A masked filled pad is not a solderable land |
| VII, filled and plated over | Fill, planarise, plate the pad over the via | Via in pad under QFN, BGA and RF ground pads | Costs the most and needs a dimple limit stated |
Every step down that list costs more and buys one property. Paying for Type VII on a via that only needed to stay clean is waste; asking Type I to do a Type VII job is a rework batch.
Which vias need more than a mask tent
Thermal vias under a power package carry heat and solder, so a tent that cracks lets paste drain into the barrel and the thermal pad ends up with voids. The count and placement of those vias is a separate question, covered under thermal vias under a power package.
Via in pad under a QFN or a BGA needs a filled and plated barrel, because the pad has to be flat enough for paste to transfer. The process detail and the traps are on via in pad with epoxy fill. Vias inside an RF ground ring sit under a shield can seam, where a dimple holds flux and a cracked tent moves the ground path. Vias in a connector zone that will take press fit pins need a plugged barrel, because a pin pushed into a hole with a mask dome in it delaminates the pad.
What goes wrong when the type is wrong
The first failure is a cracked tent. The mask dome over a 0.3 mm barrel is thin, and the outgassing of the flux underneath pushes it open at reflow. A sealed via becomes an open hole with mask fragments beside it, and those fragments are contamination next to a fine pitch part.
The second is solder wicking. On an open or badly plugged via near a connector, solder travels down the barrel and out the other side, and the joint on top measures short. It reads as a cold joint and gets chased in the profile.
The third is a blowhole or a dimple. Material plugged wet, or a barrel that was not dry, traps solvent that expands at reflow and pushes a crater through the pad. A filled via with a 40 micrometre recess does the opposite damage, taking paste that was budgeted for the joint, so the joint is short of volume rather than short of heat.
Controls that decide whether the treatment holds
Fill has to be evacuated, not just dispensed. A barrel filled at atmospheric pressure keeps a bubble at the bottom, and that bubble is the void found in the X-ray after the board is built. Planarisation then decides the pad: the published limit at the PCB end is a via recess of 10 micrometres or less after fill and plating, which keeps paste transfer predictable on a 0.4 mm pitch part.
How SUPERB PCBA handles via protection
The treatment is set from the drawing, not from a house default, because one default cannot serve a thermal pad, an RF ground ring and a non functional via on the same board. Boards come from PCB production in Jiangsu and Zhuhai with HDI to 3 stages and fine line to 0.05 mm, which is where Type VII work appears, and with a stated recess limit after fill.
Assembly runs on seven SMT lines with 3D SPI before placement, 3D AOI after reflow and X-ray with CT where a barrel sits under a joint, so a void or a recess is a measurement rather than an opinion. Release is to IPC-A-610 Class 2 or Class 3 as the drawing states, and the protection type is recorded with the lot. The board level envelope, including minimum pad and pitch, is on PCB capability.
What to put on the drawing
A note that says plug the vias is not enough. State the type per via group, the side the fill comes from, the recess limit, and whether a pad over a filled via has to stay solderable. Mark the thermal pad vias and the via in pad locations separately, because they are usually two different types on one drawing.
Questions buyers ask
Does tenting count as a sealed via?
No. A tent is a mask film over the land, and a film can crack. If nothing may pass through the barrel, the via needs a plug or a fill and the drawing should say so.
Can a plugged via be used as a pad?
Only if it is filled, planarised within the recess limit and plated over. A plug alone leaves a dimple, and a dimple under a paste deposit takes volume out of the joint.
Next step
Send the Gerber set with the via groups marked, the assembly drawing showing where a component sits over a via, and the recess limit you can accept. The reply comes back with the protection type proposed per group, the fill and planarisation route, and the inspection that will be reported for each.